How do I set up DrayTek vigor router?

How do I set up DrayTek vigor router?

The Vigor 2860 series can be setup for VDSL and PPPoE by setting the following:

1. Browse to [WAN] > [General Setup], click [WAN1] and Set the DSL mode to VDSL and the VDSL VLAN tag to 101.
2. Set the WAN mode to PPPoE and click “Details Page”
3. Enable PPPoE and input the username and password, as required.

How do I access DrayTek vigor?

How to login my Vigor Router

1. Connect a computer to one of the router’s LAN ports by an Ethernet cable.
2. Make sure the network interface is using an IP in the 192.168.
3. Open a browser on the computer.
4. After logging in, you will access the management page of the router.

How do I connect my DrayTek wireless router?

Enable Wireless LAN function on the router: Go to Wireless LAN (2.4GHz) >> General Setup, and enable Wireless LAN. 2. Change the Physical Mode of WAN 2: Go to WAN >> General Setup >> WAN2, set Physical Mode as “Wireless”, click OK to apply and reboot the router.

What is IP routed subnet DrayTek?

Non-NAT configuration (IP Routed subnet) allows using public IP addresses on LAN and bypassing NAT. You can mix public and NATted IP addresses on your LAN, so that some PCs are on your private (NATted) subnet and others have real public IP addresses. In this example the ISP has given the connection the subnet 218.25.

Does BT FTTP use PPPoE?

With FTTP, you’ll connect to the Ethernet socket on the Openreach ONT, so you just need PPPoE (so basically any router). It also applies to Cityfibre based FTTP if connecting your own router to their ONT.

Does VDSL2 use PPPoE?

The VDSL2 modem acts as an ethernet bridge. On the DSL side, it operates in PTM mode and not ATM mode, hence PPPoE rather than PPPoA. The modem encapsulates the ethernet frames from the IP router with a control header for transmission over the twisted pair to the DSLAM in the cabinet.

How do I connect to my 192.168 1.1 router?

How to Login 192.168.1.1?

1. Turn on your router and connect it to your computer with an Ethernet cable.
2. Open your favorite web browser and type “http://192.168.1.1” into the address bar.
3. Enter the correct router login/password combination.

How do I configure DrayTek as an access point?

Log in to the router’s web interface and browse to [Wireless LAN (2.4GHz)] > [General Setup]. Click OK to apply the settings. Click OK to apply that setting change. Now connect the access point from LAN port A1 to one of the LAN ports on the Vigor 2860n.

How do I setup a public IP on my router?

LAN Setup

1. Go to LAN >> General Setup, click on Details Page for IP Routed Subnet.
2. Set up TCP/IP details for IP Routed Subnet. Enable IP Routed Subnet. Enter the IP Address for the router. Note that this could be the same as router’s WAN IP.
3. For the host behind Vigor Router to obtain the public IP address, we may either:

How do I setup a public IP address?

Creating Public IP Address

1. In the left menu, click Network > Public IP.
2. Click Create.
3. Select whether you want to create an IPv4 or IPv6 address.
4. Select a server to which you want to assign the new IPv4 or IPv6 address.
5. Optional: To create a Reverse DNS, click Showin the Show other settings section.
6. Click Create.

Is there a Draytek Vigor 2950 dual WAN router?

Draytek Vigor 2950 Dual WAN Broadband Security VPN Router The DrayTek Vigor2950 series are Broadband Security VPN Routers with a Dual-WAN interface.

What kind of IP address does vigor router use?

On LAN >> General Setup >> LAN 1 Details page, you can change the IP settings. Network Administrators may use any IP subnet that is preferred, as long as it does not conflict with the WAN IP settings. By default, Vigor Router uses the subnet 192.168.1.0/255.255.255.0 for the LAN interface, and 192.168.1.1 for itself.

How to set up a DHCP server in vigor?

For advanced options, go to LAN >> General Setup >> DHCP Server Option (Advanced) Page to identify the option number, data type, and the value. (Visit DHCP Server Option for Vigor Router for some examples.) Router assign DNS server of DHCP by the following order:

How do I create a VLAN on my vigor router?

To create VLAN on Vigor Router, go to LAN >> VLAN, Check “Enable” to enable VLAN configuration on the router. Choose an available VLAN, select the physical port member (and SSID members for Wi-Fi models) of this VLAN. Select a LAN Subnet to determine which IP network settings should the router use on this VLAN.

https://www.youtube.com/watch?v=GcaZ2Pf9Ork