How do I switch between layers in Altium?

How do I switch between layers in Altium?

There are two approaches to interactively change layers during routing:

1. Press the * key on the numeric keypad. Each press of that key will move you down to the next available signal layer.
2. Use the Ctrl+Shift+Wheel Scroll shortcut combination.

How do I autoroute Altium?

Use. After launching the command, the Choose Net Classes to Route dialog will open. Select one or more net classes that you wish to route using the Autorouter then click OK – the Autorouter will attempt to autoroute all connections for all nets in the chosen net class(es) using the Main routing strategy.

How do I route multiple traces in Altium?

First select the source pad of each net to be included in the route. Shift+click to select individual pads, Ctrl+click and drag to draw a selection rectangle and sub-select multiple child pads in a component. After launching the command, you will be prompted to click to begin multi-routing.

What is interactive routing in Altium?

In the PCB editor, interactive routing is an intelligent process. After launching the command, click on a pad to select a connection to be routed. The interactive router then attempts to define a route path from that pad, all the way to the current cursor location.

How do you change layers in WoW Classic?

How to change layers in WoW Classic

1. Download and install Nova World Buffs.
2. Go to the ‘configuration’ menu.
3. Select ‘Show Minimap Layer’, and then close the menu.
4. You can now ask for a layer hop by typing “looking for Layer Hop, not Layer [X]“.

How do you toggle units in Altium?

There are some other ways to change the units of measurement in Altium Designer’s layout tool. You can use the command: “Toggle Units” found in the View pulldown menu as shown below. As with the schematic, you can also use the keystroke shortcut combination of “vu” to change the units.

How do I change the size of something in Altium?

If User Choice is selected, press Shift+V to open the Choose Via Sizes dialog, and select a preferred via size. The list of available via sizes displayed in the dialog is taken from the list of vias already used in the design, inspect these in the Pad and Via Templates mode of the PCB panel.

How do you set design rules in Altium?

Define your rules in the PCB Rules And Constraints Editor dialog, accessed by choosing the Design » Rules command from the main menus. For a detailed overview of the rules system in Altium Designer, see Constraining the Design – Design Rules.

How do I select all routes in Altium?

An easy way to select the routing is to select a single segment in the net, then press Tab to select all touching track segments on that layer. If the routing traverses multiple layers, press Tab a second time to select the routing on the other layers.

How do I mirror a component in Altium schematic?

You have to press X or Y key while you’re holding the left-click mouse button pressed on the component and it will flip. To be more explicit: Left-click on the component you want to flip, keep the mouse button pressed (like when you want to move a component with the mouse) and press X or Y key to flip.

What is net tie in PCB?

The Net Tie is a component type which allows for shorting together various nets in a design. Specifying the componet Type as Net Tie allows placing copper features between PCB footprint pads in order to facilitate connecting (shorting) various nets together at very specific locations on the PCB.

How many routes are in the Altium autorouter?

The first layer -green- contains 71 routes. The fourth layer, in blue, contains only 19 routes. The routing shown above was performed sequentially, which causes one layer to fill up before the second layer. The figure below shows what happens when using the Altium autorouter on both layers simultaneously.

How are rules resolved in Altium routing layer?

All rules are resolved by the priority setting. The system goes through the rules from highest to lowest priority and picks the first one whose scope expression matches the object (s) being checked. Online DRC, Batch DRC, during interactive routing, and while autorouting.

Which is the best autorouter for pcb design?

The Altium autorouter helps PCB designers with the difficult-to-master process of dense trace routing on a PCB. It seems like a rather simple task: connect a copper line from point A to point B with your schematic capture output as a guide. Altium Designer’s PCB autoroute tools help speed up the process of trace routing in a complex circuit board.

When to remove a connection line in Altium?

It does not matter if you choose to ignore the connection line and route the net from/to a different location, as soon as routing is terminated the net analyzer runs, and removes the connection line if it is no longer required, as shown in the animation below.