Which 2960 command assigns a VLAN to an interface?

Which 2960 command assigns a VLAN to an interface?

switchport access vlan [vlan number ] command is used to assign VLAN to the interface.

Does Cisco 2960 support NetFlow?

The switch supports NetFlow Lite running on a mixed stack configuration, where both Catalyst 2960-X and Catalyst 2960-S switches reside in the same stack. Each switch in a stack (hardware) can support the creation of a maximum of 16,000 flows at any time.

How many VLANs are initially in a Catalyst 2960 switch?

255 VLANs
The 3560 switch used in this lab supports a maximum of 1,005 VLANs locally, while the 2960 switch used in this lab supports at most 255 VLANs.

How do I add a VLAN to a Cisco switch?

You access VLAN database configuration mode by entering the vlan database privileged EXEC command. To access config-vlan mode, enter the vlan global configuration command with a VLAN ID. Enter a new VLAN ID to create a VLAN, or enter an existing VLAN ID to modify that VLAN.

How do I create a VLAN on a Cisco switch?

Configuring vlan using Config-vlan mode: 2) Create vlan using “vlan ” command and can assign name to vlan for description. 2) Issue the “interface [type] mod/port>” command in order to enter the interface configuration mode. 3) Issue the “switchport mode access” command in order to configure the port mode.

How do you configure a VLAN on a Cisco switch?

VLAN Configuration in config-vlan Mode To access config-vlan mode, enter the vlan global configuration command with a VLAN ID. Enter a new VLAN ID to create a VLAN, or enter an existing VLAN ID to modify that VLAN. You can use the default VLAN configuration (Table 12-2) or enter multiple commands to configure the VLAN.

How do I find the VLAN on a Cisco switch?

The show vlans command lists the VLANs currently running in the switch, with VID, VLAN name and VLAN status. Dynamic VLANs appear only if the switch is running with GVRP enabled and one or more ports has dynamically joined an advertised VLAN.

What is NetFlow Lite?

NetFlow-Lite collects packets randomly, classifies them into flows, and measures flow statistics as they pass through the switch. It is a true flow-based traffic-monitoring mechanism that conserves valuable forwarding bandwidth when exporting flow-based data for analysis and reporting.

Which command set a trunk port on a 2960 switch?

Solution(By Examveda Team) To set a switch port to trunk mode, which allows all VLAN information to pass down the link, use the switchport mode trunk command.

What is the purpose of VLAN 1?

VLAN 1 contains control plane traffic and can contain user traffic. It is recommended that user traffic be configured on VLANs other than VLAN 1, primarily to prevent unnecessary user broadcast and multicast traffic from being processed by the Network Management Processor (NMP) of the supervisor.

How do I see VLANs on a Cisco switch?

What does Cisco flexstack extended do on a 2960 XR switch?

Cisco FlexStack-Extended enables a long-distance out-of-the wiring-closet stack option (floor to floor). It allows back-panel stacking of up to eight Cisco Catalyst 2960-X or 2960-XR Series Switches. FlexStack-Extended can be added to a Cisco Catalyst 2960-X or 2960-XR Series Switch with a back-panel stacking slot.

What kind of power supply does Cisco 2960 XR have?

Dual redundant power supplies are supported on the Cisco Catalyst 2960-XR Series Switches. These switches ship with one power supply by default. The second power supply can be purchased at the time of ordering the switch or as a spare. These power supplies have built-in fans to provide cooling (Figure 2). Figure 2.

How does uplinkfast work in Cisco switch layer 2?

If Switch C detects a link failure on the currently active link L2 on the root port (a direct link failure), UplinkFast unblocks the blocked interface on Switch C and transitions it to the forwarding state without going through the listening and learning states. This change takes approximately 1 to 5 seconds.