What is octal bus transceiver?
This octal bus transceiver is designed for asynchronous two-way communication between data buses. The device allows noninverted data transmission from the A bus to the B bus or from the B bus to the A bus, depending on the logic level at the direction-control (DIR) input.
What is a bus transceiver?
Bus transceivers are tri-state bi-directional devices which allow the flow of data between two points making them compatible with bus-oriented systems or the bi-directional (input or output) control of interface circuitry. Bus transceivers can be inverting, the TTL 74LS242 or non-inverting, the TTL 74LS243 devices.
What is IC 74245 function?
The 74LS245 octal bus transceivers are designed for asynchronous two-way communication between data buses. The device allows data transmission from the A Bus to the B Bus or from the B Bus to the A Bus depending upon the logic level at the direction control (DIR) input.
CAN bus transceiver explain?
During normal operation, the CAN transceiver converts the single-ended logic-level output signal (TXD) from the CAN controller to a differential signal. It also converts the differential signal on the bus back to a single-ended logic signal (RXD) for input into the CAN controller.
What is the use of octal bus transceiver?
The MC74ACT640 octal bus transceiver is designed for asynchronous two-way communication between data buses. The device transmits data from bus A to bus B when T/R = HIGH, or from bus B to bus A when T/R = LOW. The enable input can be used to disable the device so the buses are effectively isolated.
What does transceiver mean?
A transceiver is a combination transmitter/receiver in a single package. While the term typically applies to wireless communications devices, it can also be used for transmitter/receiver devices in cable or optical fiber systems. In local area networks, the transceiver is a part of the network interface card.
CAN transceiver voltage levels?
Standard CAN bus transceivers operate over a limited common mode voltage range that extends from −2V to +7V. In commercial or industrial environments, ground faults, noise, and other electrical interference can induce common mode voltages that greatly exceed these limits.
What is transceiver circuit?
Explanation: A transceiver circuit is a buffer that can operate in both directions right as well as left. Explanation: UART means Universal Asynchronous Receiver/Transmitter which converts the bytes it receives from the computer along parallel circuits into a single serial bit stream for outbound transmission.
What is a transceiver made of?
In radio communication, a transceiver is an electronic device which is a combination of a radio transmitter and a receiver, hence the name.
What is a transceiver used for?
The transceiver is an important part of a fiber optics network and is used to convert electrical signals to optical (light) signals and optical signals to electrical signals. It can be plugged into or embedded into another device within a data network that can send and receive a signal.
CAN bus transceiver?
The CAN transceiver is the CAN physical layer and interfaces the single ended host CAN protocol controller with the differential CAN bus found in industrial, building automation, and automotive applications.
CAN bus signal voltages?
What does the sn54 / 74ls245 octal bus transceiver do?
The SN54/74LS245 is an Octal Bus Transmitter/Receiver designed for 8-line asynchronous 2-way data communication between data buses. Direction Input (DR) controls transmission of Data from bus A to bus B or bus B to bus A depending upon its logic level.
What kind of transceiver is an octal bus?
OCTAL BUS TRANSCEIVER The SN54/74LS245 is an Octal Bus Transmitter/Receiver designed for 8-line asynchronous 2-way data communication between data buses. Direction Input (DR) controls transmission of Data from bus A to bus B or bus B to bus A depending upon its logic level. The Enable input (E ) can be used to isolate the buses.
How does the snx4ls245 device allow data transmission?
The SNx4LS245 devices allow data transmission from the A bus to the B bus or from the B bus to the A bus, depending on the logic level at the direction- control (DIR) input. The output-enable (OE) input can disable the device so that the buses are effectively isolated. Device Information(1) PART NUMBER PACKAGE BODY SIZE (NOM)