How do you reset a meter reading?

How do you reset a meter reading?

Resetting a meter register to zero

1. Open Connect Utility Management > Meters > Enter Meter Activity.
2. Enter the Customer Number. Press Enter.
3. Select an Action Code. Select the action code to reset a meter reading.
4. Press Enter.
5. Press Enter again.
6. Enter the New Meter ID.

How do you read a dial power meter?

Dial meter

1. Stand directly in front of your meter.
2. Read the dial on the left first. (Ignore the dial underneath).
3. Look at the two numbers the pointer is between and record the lowest number. (If the pointer is between 9 and 0, record 9.)
4. Do the same with each dial, reading left to right.

How can I test my electric meter?

You need to switch off all your electrical lamps/appliances, etc. Now record the reading of your electrical meter and let only 1000 watt lamp run for one hour and then record the final reading. If the difference of reading is one unit i.e. 1 KWH, it means that meter is working satisfactorily.

How do you reset a meter?

The front panel of the meter has a reset button on it. If pressing the RESET button does not set all of the readings back to zero, you can hold the ENTER button and simultaneously press the RESET button.

How do you read a single rate electricity meter?

Single-rate digital electricity meters

1. Write down all the numbers before the decimal point, from left to right.
2. Ignore any numbers after the decimal point (which may be shown in red).
3. To take a reading, start with the left dial and write down the number indicated by the pointer on each dial, moving towards the right.

How do you read electric A and B buttons?

If your meter has an ‘A’ and ‘B’ button, press ‘A’ until you get to TOTAL ACT IMPORT. The number below this is your electricity reading. Your meter might have three buttons to the side of the display. If this is the case, just press the middle button, and the display will show your reading below the ‘IMP’ on screen.

How do I read my electric meter kWh?

To figure the number of kilowatt-hours you used during the month, subtract the last month’s reading on your most recent bill from the present reading. This will give the kilowatt-hours you used for the period.

How do I read my digital electric meter?

Digital meter

1. Read the numbers from left to right, ignoring any numbers shown in red.
2. Ignore any digits in a red surround.
3. Ignore any printed zeros.
4. Ignore any digits after the decimal point.

How do I know if my electric meter is faulty?

If your power goes out and there is no electrical outage in your area, you could have a broken electric meter. Sometimes, heavy storms can cause the electric meter to break or pull away from your home. If the connection is broken from the meter to your home, it stops working and so does the power.

What to do if electric meter is not working?

If the meter is faulty/damaged or not functioning, then consumer should immediately report to the concerned electricity billing /sub division office as applicable and get it repaired/replaced/get new meter. It is the sole responsibility of the customer to make sure the safety of meters.

Who is the owner of Ampy Email metering?

Ampy Email Metering is a division of Emwest Products Pty Ltd, ABN 78 002 894 224, which is a wholly owned subsidiary of Bayard Capital. Products produced by Ampy Email Metering are branded with the company logo Ampy Metering.

Is the model 1010 gas meter pulse ready?

Every Model 1010 gas meter is supplied pulse ready so that the meter can be retrofitted with a pulse output module for advanced metering applications without the need to replace the meter index. The Model 1010 is also available with a top reading index, allowing ease of reading when the meter is installed at ground level.

Is the model 1010 a ground level meter?

The Model 1010 is also available with a top reading index, allowing ease of reading when the meter is installed at ground level. The model 1010 is also available with Viton o-rings for aggressive gas applications.

How much does a Landis Gyr pulse meter weigh?

Weight 2.80 kg Pulse Output Ready All meters are fitted with a magnet in the far right index wheel and hence each meter is pulse retro fittable in the field 1 pulse / 10 lts. Corrosion Protection Alodine internal and external pre-treatment of castings followed by baked Woodland Grey polyester powder coat for maximum corrosion protection.