What are the 6 steps of the problem solving method?

What are the 6 steps of the problem solving method?

Six step guide to help you solve problems

• Step 1: Identify and define the problem. State the problem as clearly as possible.
• Step 2: Generate possible solutions.
• Step 3: Evaluate alternatives.
• Step 4: Decide on a solution.
• Step 5: Implement the solution.
• Step 6: Evaluate the outcome.

What is the 6 point technique?

The six point fault finding technique has six steps: 1. Test the system, i.e. make measurements or collect other evidence, 2. Analyse the reading, 3. Repair the fault, 6. Retest the system.

What are the six key steps to approach electrical fault finding?

What are the six key steps to approach electrical fault finding?

• Collect the Evidence. All the evidence collected must be relevant to the problem in hand.
• Analyse the Evidence.
• Locate the Fault.
• Determination and Removal of the Cause.
• Rectification of the Fault.
• Check the System.

What are the steps of problem solving method?

8-Step Problem Solving Process

1. Step 1: Define the Problem. What is the problem?
2. Step 2: Clarify the Problem.
3. Step 3: Define the Goals.
4. Step 4: Identify Root Cause of the Problem.
5. Step 5: Develop Action Plan.
6. Step 6: Execute Action Plan.
7. Step 7: Evaluate the Results.
8. Step 8: Continuously Improve.

What are the six steps of the problem solving method quizlet?

Terms in this set (6)

• Problem Solving: 1. ID Problem.
• Problem Solving: 2. Developing goals.
• Problem Solving: 3. Collecting Data.
• Problem Solving: 4. Developing Plans.
• Problem Solving: 5. Select best plan.
• Problem Solving: 6. Implementing the plan/execution.

What is emergent problem sequence?

Emergent problem sequence is related to identifying if anything has changed recently. getting the fault found as quickly as possible. dealing with an emergency.

How do you identify faults?

To correctly identify a fault, you must first figure out which block is the footwall and which is the hanging wall. Then you determine the relative motion between the hanging wall and footwall. Every fault tilted from the vertical has a hanging wall and footwall.

How do you find fault in a circuit?

How to identify electrical faults

1. Switch off the main power at the consumer unit/fuse box.
2. Or switch off the breaker and lock it if you can.
3. Attach a note to the unit to advise you are working on the circuit.
4. Check the circuit is dead with a socket tester or voltage tester/meter for lighting circuits.

What is the first step to take when there is an electrical fault?

When you have an electrical breakdown at home the first thing to do is to check that the switches on the circuit breaker panel are all raised, including the general switch and the differential. If everything is correct, the next step is to lower the centre switch and wait five to ten seconds before raising it again.

What are the 7 steps to problem-solving?

Effective problem solving is one of the key attributes that separate great leaders from average ones.

1. Step 1: Identify the Problem.
2. Step 2: Analyze the Problem.
3. Step 3: Describe the Problem.
4. Step 4: Look for Root Causes.
5. Step 5: Develop Alternate Solutions.
6. Step 6: Implement the Solution.
7. Step 7: Measure the Results.

How is the six step method used in problem solving?

The Six-Step method provides a focused procedure for the problem solving (PS) group. It ensures consistency, as everyone understands the approach to be used. By using data, it helps eliminate bias and preconceptions, leading to greater objectivity.

What are the steps in a six step troubleshooting plan?

In L623, the Six-Step Troubleshooting Plan was introduced. These steps are: 1. Verify the complaint 2. Determine the related symptoms 3. Analyze the symptoms 4. Isolate the trouble 5. Correct the trouble 6.

What are the six key steps to electrical fault finding?

What are the six key steps to approach electrical fault finding? Here are six key points to consider: 1. Collect the Evidence All the evidence collected must be relevant to the problem in hand. If one is in doubt as to whether anything is relevant, then include it. Reject it afterwards at the first opportunity if it clearly is not relevant.

What to look for when troubleshooting a circuit?

Observation and equipment history are important in troubleshooting complex circuits and there are a couple of things that can be looked at. First of all, we’ll mention logbooks. Logbooks often can provide a history of component failure.