What is a 41 blower motor fault?

What is a 41 blower motor fault?

“BLOWER MOTOR FAULT – Indicates the blower failed to reach 250 RPM or the blower failed to. communicate within the prescribed time limits. Thirty seconds after being turned ON or ten. seconds during steady-state operation.”

How do you read a Bryant furnace error code?

Like many furnace manufacturers, Bryant uses flashing LED lights to indicate error codes that can give you an idea of what’s wrong with your furnace when it’s not functioning properly. The short flashes indicate the first digit of the two-digit code, and the long flashes indicate the second digit.

How do I reset my Bryant heat pump?

How to Reset a Bryant Air Conditioner Split Unit

1. Locate the electrical service box in your home.
2. Open the electrical service box and locate the circuit breaker that corresponds with your Bryant split unit air conditioner and heating system.
3. Flip the appropriate circuit breaker to the “Off” position.

Where is the blower motor control module?

It’s located inside the dash, often on the opposite side of the steering wheel or inside the engine compartment on the firewall. A blower motor resistor or a blower motor control module is the part that controls the speed of the blower motor.

What does a solid red light on my Bryant furnace mean?

A solid red LED is a code. It means the board is normal and waiting for a heat call. Your blower is running and you aren’t getting a call for heat.

How do you reset a Bryant?

Bryant air conditioners are no different. However, unlike other companies that manufacture air conditioners, the brand doesn’t have a reset button on the air conditioner. You have to reset the device by resetting the circuit breaker in your house.

How do I reset my Bryant thermostat?

Bryant Thermostat Reset

1. Open the door.
2. Press and hold the right up and down buttons. simultaneously for about five seconds.
3. The padlock symbol disappears. This unlocks the keyboard and can be used. The keyboard is reset. Return to the locked state after pressing and holding for two minutes.
4. Close the door.

How do I get my furnace out of lockout mode?

Most modern gas furnaces can be reset by turning off the power, waiting around 20 seconds, then switching the power back on. Other furnace models may exit lockout after 1-2 hours and attempt to power on again. If your furnace has a pilot light, you may need to relight it following the manufacturer’s instructions.

How do I know if my blower motor control module is bad?

Symptoms of a bad heater blower motor resistor

1. Fan does not work at all, so no air comes out of the vents.
2. Fan only works on some speeds and not others.
3. Fan only works on the highest speed.
4. Fan runs all the time and can’t be controlled with the fan switch.
5. You see smoke coming out of the vents.

What does code 41 mean on a Bryant furnace?

Error code 41 on a Bryant or Carrier furnace is the notice for a blower motor fault. Short of replacing the blower, what do I do to fix it? Error code 41 can happen when the blower fails to reach the 250 rotations per minute threshold. In that case, it could simply be a matter of adding oil to the blower motor.

How can I tell if my Bryant furnace is not working?

New models utilize flashing LED lights to show error codes that help you identify your furnace’s problem when it’s not correctly running. The short flashes will present the first digit of the two-digit code, whereas the long moments will inform the second digit.

Why does my Bryant furnace have a Green led 4 on?

You will need to replace the primary control board when the LED2 keeps reappearing. If that happens, the furnace is running in high heat. A green LED 4 on means that your unit is running in low heat. Should the line voltage polarity be reversed, a red LED2 will be flashing.

What does error code 13 on Bryant furnace mean?

When your furnace displays error code 13, the limit switch is tripping due to various problems. Typically, your Bryant furnace will auto-reset after 3 hours. Error code 14 signals problems with ignition. It will take three hours until the control will reset automatically.