How do I assign a VLAN to an IP address?
Here are the steps to configure an IP address under VLAN 1:
- enter the VLAN 1 configuration mode with the interface vlan 1 global configuration command.
- assign an IP address with the ip address IP_ADDRESS SUBNET_MASK interface subcommand.
- enable the VLAN 1 interface with the no shutdown interface subcommand.
Do I need to assign an IP to a VLAN?
VLANs do not really have IP addresses assigned to them. They have a network assigned to them, or a subnet, or a network range, however you want to refer to it.
How do I configure VLAN on HP switch?
To configure basic settings of a VLAN interface:
- Enter system view, use the command: system view.
- Create a VLAN interface and enter VLAN interface view. interface vlan-interface vlan- interface-id.
- Assign an IP address to the VLAN interface.
- Configure the description of the VLAN interface.
- Bring up the VLAN interface.
How do I assign an IP address?
Setting the IP address on your PC or mobile computer
- Click Start >Settings >Control Panel.
- On the control panel, double-click Network Connections.
- Right-click Local Area Connection.
- Click Properties.
- Select Internet Protocol (TCP/IP), and then click Properties.
- Select Use the Following IP Address.
Is there an IP address assigned to VLAN 1?
VLAN 1 has a static IP address, while VLAN 2 has a dynamic IP address assigned via DHCP or PPPoE from the uplink device. You can enable the DHCP/PPPoE client multiple uplink VLAN interfaces (up to four) on the managed device; these VLANs cannot be VLAN 1.
What is VLAN interface IP address?
Same thing, the VLANs IP address is a Switch Virtual Interface (commonly called a SVI), in essense it is an interface (albeit logical) and plays the same role as a routers interface which has an IP address. It provides a gateway for inter-VLAN or inter-routing traffic.
How do I find the VLAN details on my HP switch?
Specifies a single port number or a range of ports (for example, a1-a16 ) , or all for which to display information. Displays detailed VLAN membership information on a per-port basis….Syntax:
Port name | The user-specified port name, if one has been assigned. |
---|---|
VLAN ID | The VLAN identification number, or VID. |
How do I remove a port from a VLAN HP ProCurve?
Removing VLANs from a physical port
- From global configuration mode, enter interface Ethernet configuration mode. device(config)# interface ethernet 1/1/1.
- Enter the remove-vlan all command to remove all VLANs from the Ethernet port. Enter the remove-vlan vlan command to remove the VLANs from the Ethernet port.
How do I assign an IP address to my HP switch?
Click on Quick Setup. In the Switch Quick Setup Parameters box, click on Change. Enter the IP address and any other information such as the Subnet mask and Gateway. Click on Save to save changes.
Can a HP ProCurve switch be used as a VLAN?
This article provides instructions on VLAN configuration of HP ProCurve switches. The examples below are performed on a J9022A 48-port model, but the syntax should also work with other ProCurve models.
Can a device Ping the IP address of a VLAN?
Once the IP addresses are set on each VLAN, devices in those VLANs will be able to ping the IP address of the VLAN as long as they have the same network and subnet scheme. NOTE: this form DOES NOT e-mail this article, it sends feedback to the author.
How does a VLAN on a NIC work?
If for example you were to go into the NIC settings on a computer and set a VLAN on that nic then it would be tagging traffic on that VLAN. WiFi Access points and IP Phones are set to tag traffic in many cases. If you went into your access point and set an SSID to be associated with a VLAN, then it’s tagging traffic on that VLAN.
Do you need router to talk to different VLANs?
In order for devices on different VLANs to talk you must have a router that sends traffic between them. The router can be a layer 3 switch and this is often preferred over a firewall as many firewalls aren’t designed to route at wire speed.