How do you reset the anti theft system on a Chevy Malibu?

How do you reset the anti theft system on a Chevy Malibu?

Reach in through the window and turn the key to ‘half I’m (as opposed to full on). Then leave it sit for 10 minutes until the anti theft light stops blinking. Then reach in through the window, take the key out fully, then re insert key and start car while standing outside. Only thing that has ever worked.

How do I get my car out of anti-theft mode?

Step 1: Insert the key into the door lock. Use the side door on the driver’s side and the physical key even if there is a keyless entry system on the car. Step 2: Turn the vehicle key to unlock the car door without releasing it. Hold the key for 30 seconds in the position.

How do I reset my Chevy anti theft system?

How Do I Reset Anti-Theft System: Chevy Silverado?

1. Insert ignition key.
2. Turn it to the on position.
3. Attempt to start the engine.
4. Leave the key in that position until the security light stops flashing.
5. Once the light goes off, switch the ignition key to off.
6. Wait about five seconds.
7. Try to start the engine again.

How do I clear my anti theft system?

Exit the car with all doors closed and the windows rolled up. Also close and any rear doors such as the trunk, rear hatch and front hood. Lock the car using the drivers side lock and walk away from the car at least ten feet. Wait for fifteen minutes and unlock the door, this should reset the security system.

How do you reset the security system on a 2006 Chevy Malibu?

To reset the alarm on the 2006 Chevy malibu you need to lock all the doors, then unlock the driver side and put the key into the on position. Now turn it off and then back on twice and it will reset.

How do you reset the anti theft system on a 2009 Chevy Malibu?

If you need to reset the alarm on your 2009 chevy malibu, tuen your key counter clockwise and then turn it clockwise to lock your vehicle’s doors. Repeat this process and the anti-theft system should be reset.

How do I disable anti theft alarm system?

Turn the key to unlock your car door, but don’t release it. Hold the key in this position for 20 to 30 seconds. This lets the system know you have the correct key, and it can allow you to bypass the alarm system. Some vehicles recognize the key simply by turning the key back and forth in the door lock key cylinder.

How do I reset my car alarm after changing the battery?

Use a wrench to loosen the nut of the negative terminal and remove the wire from the battery. Step 3: Reattach the wire. After about a minute, reattach the wire. This should reset all of your electrical systems including those that power the alarm.

How do I reset my alarm without the code?

How to reset a house alarm without a code or you’ve lost it?

1. Go to your alarm system’s main access panel.
2. Remove the power plug to the alarm console from the socket.
3. Unlock and open the main panel with the console access key, or a small tool, such as a screw.
4. Disconnect one of the wires from the system’s main battery.

How do I disable GM Anti-theft system?

How to Disable a GM PassLock System

1. Leave the ignition key turned to the “On” position after the vehicle has stalled and will not start.
2. Look at the dashboard and locate the theft system light.
3. Turn the ignition to the “Off” position to disable the PassLock system, and wait for 20 seconds for the system to reset.

How do you turn off anti theft on a 2007 Chevy Malibu?

In order to reset the anti theft system on Your 2007 Chevy Malibu You’ll first need to put the key in the ignition and move it in to the on position. Now let the vehicle sit for 10 minutes. The light should stop blinking and when it does You’ll need to take the key out of the ignition.

How do you turn off the anti theft system on a 2006 Chevy Malibu?