How do I fix F01 on my Whirlpool washer?

How do I fix F01 on my Whirlpool washer?

The F01 indicates a failed electronic machine control board. This error code can sometimes be caused by a glitch or power surge through the electrical lines. You may be able to clear this code by unplugging the washer for 5 minutes. Be sure to unplug the washer before accessing internal components.

How do I reset my Whirlpool Duet washer F01?

You can try and reset the error by killing power to the washer at the breaker for one minute or unplugging the washer for one minute. Restore power and if the error persists you will need to replace the main control board.

What does error code F01 mean on a Whirlpool Duet dryer?

The F01 error code means the primary control unit in the dryer has failed and will have to be replaced. The control that needs replacing is the electronic control board not the user interface and/or control panel.

What does E01 F01 mean on a washing machine?

central control unit
0. E01 F01 is a very straight forward error for these Maytag Maxima washers. The error means your CCU (central control unit) has failed and will need to be replaced. The CCU is the main control board for your washer and it’s located under the top panel of the washer in the front right corner.

What does fo1 mean on washing machine?

Electronic circuit board fault
F01 — Electronic circuit board fault. Issue: Washing Machines is not operating – some or all functions are not selectable. Advice: We recommend you disconnect (unplug) the appliance from the mains supply for a minimum of 2 minutes. Reconnect supply and wait 30 seconds and try starting the machine again.

How do I fix E01 on my washing machine?

How to Diagnose and Fix Fault Code E01

1. Switch off and unplug your machine.
2. Check the door lock itself. (Sometimes the plug on the lock can melt.)
3. Check the wiring to the door lock.
4. Check the wiring to the control board from the door look.

How do I reset my Whirlpool front load washer?

Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.

How do I fix F01 error?

The Whirlpool Duet Dryer F01 error may be able to be fixed with a simple reset of the main control. Unplug the dryer for 1 minute and plug it back in this will reset the control if the error persists after that you will need to check the dryer thermal fuse.

What does F1 and e1 mean on a Whirlpool dryer?

A “F1E1” code in the display indicates there may be an issue with the control unit or the associated wiring. Touch POWER, select a cycle, then hold START/PAUSE button to start the dryer. If this is unsuccessful, unplug the dryer.

How do I fix Hotpoint F01?

When your washer dryer shows error message F01, we advise you to disconnect and unplug your Hotpoint washer dryer from the mains supply for 3 minutes. After 3 minutes have passed, reconnect your Hotpoint washer dryer and wait 30 seconds before you start up the machine again.

How do I fix error code F01 Indesit washing machine?

Indesit error F01

1. Turn off the washing machine and unplug the connector.
2. Wait 2 minutes and put the connector back in.
3. Wait 30 seconds and turn the washing machine back on.

What does Whirlpool duet washer error code F- mean?

The Whirlpool Duet washer has a series of error codes that indicate specific problems. The F/dL code indicates a door lock error on the machine. When the door fails to lock to allow the cycle to begin, it attempts to lock itself at least six times before the error appears on the digital display screen.

What does the code F2 mean on a whirlpool duet washer?

The F2 error code on the Whirlpool washer is indicated as F02, and means that the washer is taking too long to drain properly. This means there is come kind of problem with the washer’s draining system.

What does F01 mean on a whirlpool duet dryer?

Whirlpool Duet Dryer F01 Error. The F01 error code means the primary control unit in the dryer has failed and will have to be replaced.

What does Whirlpool Cabrio F1 error code mean?

Whirlpool Cabrio Washer Error F1. The Cabrio Washer F1 error code happens when the main control board gets a bad signal from the water level pressure switch circuit. This is normally caused by a pinched or ripped water level pressure switch hose. Steps to take to try and remedy this error are listed below.