How does a flood safe hose work?
FloodSafe™ is actuated by flow of cold or hot water in excess of the design flow rate indicated on the label. Once a downstream flow of water in excess of the flow required by any standard fixture/appliance is detected, FloodSafe™ assumes a burst and the flow of water is shutoff.
What is a flood safe hose?
These are special flexible water supply connectors, aka ‘hoses’, with a mechanism that will completely shut off the flow of water if the hose bursts. These connectors are made for faucets, toilets, ice makers, dishwashers, and washing machines, and can be identified by an extra length of metal at the hose inlet.
How does Eastman Flood Defender work?
The Flood Defender by Eastman is a 10-foot universal ice maker connector with a 1/4-inch inlet that prevents potential damages caused by ice maker leaks. It is designed with a built-in auto-shut-off valve that activates when excess water flow is detected, protecting your floors and surrounding fixtures.
What is a leak limiting hose?
repaired. Water supply connected with leak- limiting hoses. Hoses designed to limit leaks can trip falsely. and prevent the washer from filling.
How does a flood stop valve work?
A. In their normal position, the FloodStop valves are open and will allow water to pass through; once water touches their sensor, the motorized ball valve is tripped and the valves are closed. The valve(s) will remain closed until the sensors are dried and the reset “Open” button is pressed.
What is an aquastop hose?
The Water Safety System or ‘Aqua Stop Valve’ has been invented for leakage prevention. It is attached to the water supply hose and automatically cuts off water flow when hose gets damaged.
Are dishwasher hoses Universal?
Purpose – This universal dishwasher drain hose can be used to connect many brands of dishwashers to the drain. In addition, the DWDH78 is designed to be used as an extension to existing drain hoses when cut at the designated place.
What is a burst protector?
Description: Burst Guard Nylon Hose Sleeve from Tompkins is an ultra-dense, two-layer sleeve that is three-times the density of standard sleeve. This smooth-bore sleeve is easily installed over hose, chains, cables or springs and may be secured with nylon cable ties or band-clamps.
How long do braided supply lines last?
The general rule of thumb is to replace all your supply line hoses every 5 years as a preventative measure to protect your home against any potential leaks. But since braided supply lines have a rubber core, we recommend that they can be replaced every 10 years.
How to turn off floodsafe on 2nd floor toilet?
Assuming you have installed a FloodSafe Auto-ShutOff value on 2nd floor toilet. 2. Go to basement, shut off the main water supply value for the whole house 3. In basement or on main floor, turn on any water tap for 1 min. This will make water drain from second floor and to create air in the pipe due to gravity.
How do I Turn Off the floodsafe water supply?
Close the shutoff valve to shut the water supply to the FloodSafe™ connector 2. Disconnect the FloodSafe™ at the shutoff valve. This will automatically reset the FloodSafe™ device. 3. Reconnect the FloodSafe™ according to installation instructions and turn on water supply to full open position.
What do you need to know about the floodsafe system?
The FloodSafe’s patented design protects against catastrophic water damage caused by burst, broken or ruptured water supply hoses and fittings. FloodSafe™ connectors include a standard braided stainless steel flexible hose and a FloodSafe™ shutoff device located on the inlet.
How does the Watts floodsafe auto shutoff connector work?
First, let’s understand how it works. There is no electronic component inside these connectors, everything is mechanical. Quote from Watts’ web site “When flow of water in excess of the flow required by any standard fixture/appliance is detected, FloodSafe assumes a burst and the flow of water is shutoff”.