What is Arctic Silver used for?
Arctic Silver Inc. is a privately owned engineering corporation which develops and manufactures thermally conductive compounds and thermal adhesives for the application of heat sinks to high-powered electronic components such as processors, LEDs, chipsets and other electronic devices.
How do you use Arctic Silver thermal adhesive?
Mixed in the proper ratios, Arctic Silver Thermal Adhesive has a pot life of 3 to 4 minutes at normal room temperatures. Dispense the proper proportions of resin and curing agent onto a clean plastic or metal sheet. Only use as much as you will be able to mix and apply in approximately three minutes.
Does Arctic Silver need to cure?
According to Arctic Silver, up to 200 hours of break-in time is required for the Arctic Silver 5 thermal paste to “cure” and its performance to stabilize.
How long is Arctic Silver Good For?
Even in extreme conditions the paste between a HSF should last 6 months before drying. If kept in a tube (and sealed/cool) the thermal paste will last hundreds of times longer. In other words, no worries. Far more important is how you apply the paste and mate the heat sink to the chip.
What is Arctic Silver made of?
The current version of the company’s eponymous thermal interface material, Arctic Silver 5, is a compound of silver, aluminum oxide, zinc oxide, and boron nitride in a polysynthetic oil base.
How do you apply thermal adhesive?
One of the most common methods used is often referred to as the “line method”. This is exactly as it sounds. Apply a thin line of thermal paste directly down the center of the IHS (Integrated Heat Spreader) and then allow the pressure of the CPU cooler to spread the paste as you secure it.
Who makes Arctic silver5?
Arctic Silver 5 is 6th from left (in the custom grey and silver syringe with the fat black cap), and ArctiClean steps 1 and 2 bottles in the background….Arctic Silver.
Type | Private |
---|---|
Founder | Nevin House |
Headquarters | Visalia, California |
Products | Thermal interface materials |
Website | www.arcticsilver.com |
How long does it take Arctic Silver 5 to set?
From Arctic silver: ” it will take a up to 200 hours and several thermal cycles to achieve maximum particle to particle thermal conduction and for the heatsink to CPU interface to reach maximum conductivity. “
Is Arctic Silver still the best?
The Arctic Silver 5 AS5 is a good choice for people who are looking to apply paste to multiple CPUs. It’s designed to last 8 years, which means your CPU will probably be outdated before your paste needs to be changed.
How often should you Repaste?
How Often Should You Replace Thermal Paste? In most cases, you shouldn’t need to reapply more than once every few years, though you should replace your paste if you remove your cooler for any reason. You may also want to consider reapplying thermal paste if you find your CPU temperatures are climbing.
Is the Arctic Silver adhesive good for electricity?
Arctic Silver Thermal Adhesive was formulated to conduct heat, not electricity. NOTE: Even though Arctic Silver Thermal Adhesive is specifically engineered for high electrical resistance, it should be kept away from electrical traces, pins, and leads.
Are there any problems with Arctic Silver thermal epoxy?
Even though Arctic Silver Thermal Epoxy is specifically engineered for high electrical resistance, it should be kept away from electrical traces, pins, and leads. The cured epoxy is slightly capacitive and could potentially cause problems if it bridged two close-proximity electrical paths.
What should Arctic Alumina thermal adhesive be kept away from?
Arctic Alumina Thermal Adhesive should be kept cold and away from UV light (sunlight and florescent lighting). We recommend refrigerating the unused material and allowing it to come to room temperature prior to use. Arctic Alumina Thermal Adhesive is a permanent adhesive.
Can you use Arctic Silver on a CPU heatsink?
It is NOT intended to be used between a CPU and the CPU heatsink. On a CPU please use a thermal compound such as Arctic Silver 5, Céramique 2, or Arctic Alumina. For proper use refer to the instructions here. Made with 99.8% pure micronized silver. 62% to 65% silver content by weight.