How do I connect my Belkin router to the Internet?

How do I connect my Belkin router to the Internet?

1. Connect to your network. Use your mobile device or computer to connect to the wireless or wired network being broadcast by your Belkin router.
2. Visit the Belkin router login IP. Open your favorite web browser and visit the default Belkin login IP address: 192.168.2.1.
3. Enter the login password.
4. Change the default password.

How do I manually configure my router?

Change Wireless Router Settings

1. Connect to your network wirelessly, or via ethernet.
2. Find your router configuration page.
3. Log in with the username and password.
4. Find the Wireless Settings page.
5. Set the new channel, usually with a dropdown menu.
6. Your router will now reboot.

What is Belkin router IP address?

192.168.2.1
NOTE: The default IP address of a Belkin router is 192.168. 2.1. You need to check the IP address range and Default Gateway to assign it to a computer when assigning a static IP address.

How do I setup my Belkin Wifi Booster?

To do this, simply press the range extender’s reset button for at least 10 seconds while it is turned ON. Power cycle the range extender then connect to the network again. Wait for your device to connect to the Belkin. setup network before proceeding to the next step.

How do I reset my Belkin wireless router?

Reset Button

1. Locate the “Reset” button on the Belkin router.
2. Push the “Reset” button and then release it to reset the router.
3. Push the “Reset” button and hold it for at least 10 seconds to start the “Restore to Factory Defaults” process.
4. Release the button after the 10-second minimum.

How do I setup my Belkin router without a modem?

How do I setup my Belkin router without a modem? Associate the modem to your Belkin router using an Ethernet cable. The Ethernet link must be connected to an open Ethernet port on your modem, and into the port on your Belkin router labeled “WAN/Internet.” Reconnect your Internet modem to its capacity supply.

What should my router settings be?

Generic Optimal Router Settings Guide

• 802.11 n Support. Enable: Faster speed by supporting N or later wifi tech.
• WMM Settings. Enable: Many mobile devices like iphone and ipad need it to function.
• 2.4 Ghz vs 5 Ghz.
• 20 Mhz or 40 Mhz (And Best Wireless Channel)
• AP Isolate.
• IP Flood Detection.
• Multicast Rate.
• Preamble Type.

How do you get to your router settings?

Find Your Router’s IP Address You log into your router’s firmware through a browser. Any browser will do. At the address field, type the IP address of your router. Most routers use an address of 192.168.1.1.

How do I reset my Belkin router to factory settings?

How do I access my Belkin wireless router?

Go to command promt and type ipconfig. You will get the ip address of your computer as well as the default gateway address under Ethernet adapter Local Area Connection. Type that default gateway address in your browser, you will get the belkin page. You can use default username and password as admin to access the page.

How do I make Belkin router secure?

If you just configured your brand new Belkin router, you need to secure the wireless network by editing the default security settings of the router. You can quickly access the security settings by navigating to the device’s Web interface. After you secure the network, you need to prevent access to the router by creating a password.

Are Belkin routers good?

For some people, yes, that would be a good router for them. Technically speaking, a Belkin router for a SOHO solution is typically just fine and with that level of tech, you get about 5–10% failure rate.

What is the default password for a Belkin router?

Default Passwords for Belkin Routers. By default, all Belkin routers’ default username and password is admin (username) while “blank” (leave it blank) for the password. You need to properly connect the router to your modem and PC before you can access the router using a web browser (IE, Firefox, Chrome, etc.).

https://www.youtube.com/watch?v=OxHEBfy_8zA