How much does a 3406E head weigh?
Additional information
| Weight | 450 lbs |
|---|---|
| Dimensions | 48 × 42 × 18 in |
Is a cat 3406E a good engine?
In terms of failure, the 3406E is actually pretty good, especially compared to some other Caterpillar engines. However, like all engines, they still had their issues. This was fixed when the engine upgraded to the C15, and seals replaced gaskets, along with a new block design.
How much horsepower does a cat 3406E have?
600-hp
“Driveability is tremendous with the 600-hp engine, even when carrying a heavy load.” The new 3406E is loaded with a long list of special features that allow it to stand out on the job. Cat is offering the new engine as a powerplant with a million-mile life to overhaul.
Is a cat 3406E a C15?
The C15 was made to improve on the 3406E. One of the key improvements is that C15 engines see oil leakage less frequently than the 3406E.
How much does a 6nz cat weigh?
The displacement is 15.2 liters, or 928 cubic inches. The power rating when used in a truck or bus is 435 to 625 horsepower at 2,100 rpm; RV and fire truck ratings are 600 to 625 horsepower at 2,100 rpm. The total torque output is 1,550 to 2,050 foot-pounds at 1,200 rpm. Total weight of the engine is 3,090 pounds.
How many liters is a cat 3406b?
General
| Engine Configuration | Inline 6, 4-Stroke-Cycle Diesel Inline 6, 4-Stroke-Cycle Diesel |
|---|---|
| Stroke | 6.5 in 165 mm |
| Displacement | 893.4 in³ 14.6 l |
| Compression Ratio | 14.5:1 14.5:1 |
| Aspiration | Turbocharged Aftercooled Turbocharged Aftercooled |
Is a 3406E a 6NZ?
6NZ is a 14.6L. 3406E’s were used in the 2000’s. 40 pins in the 99 and 70 pins introduced in 99 as well. 3406Es are prefix’s 5EK (14.6L), 6TS (14.6L), 1LW (14.6L), 5DS (15.8L) all 40 pin ecms.
How many gallons of oil does a 3406E hold?
Formerly the capacity was 36 quarts or 9 gallons. The new 120-8972 Oil Level Gauge (dipstick) is available to retrofit MOST existing engines to measure the increased capacity. The new dipstick will fit both front and rear sump non-Brake Saver applications. The new dipstick is NOT a full range dipstick.
What is a 6NZ?
It is a serial number prefix that cat used to identify a series of engines, the 6NZ is the last good single turbo C15, anything after that and your looking at probems created by updated programming and changes in parts used to meet emmissions.
How much does a 3406e Caterpillar engine weigh?
Size and Weight The 3406 has a total dry weight of 6,819 pounds without any engine accessories installed. Measuring from the end of the engine to the end of the flywheel housing, the length of the engine is 117.28 inches while the overall width is 39.22 inches.
What year was 6NZ come out?
2002 down. 6NZ engine designation. The MBN isthe “bridge” engine before the Acert.
Can a Caterpillar 3406 cylinder head be replaced?
Bring your Caterpillar 3406 engines back to life with cylinder heads from Diesel Parts Direct. Overheating of diesel engines can warp the head, letting oil and water into the wrong places. When it’s time for replacement, look no further than Diesel Parts Direct for a range of cylinder heads to suit the 3406b, 3406e and everything in between.
Can a cat Reman head be used as core?
Always use Cat ReMan heads, and yes they take em all back as core, but melt and scrap busted ones. Never see a welded Cat head, and they run $2k+ with a core. Did you find the recommended reading relevant to this discussion?
How much does a cat head rebuild cost?
We work with a guy who had a valve and guide come apart a few hundred miles after his cat rebuild with a cat head. Our shop has only ever done 1 rebuild with aftermarket parts. It lasted 20,000 kms and the liner broke apart and then pounded into the head. Click to expand… The best I can figure for a new head is $3700.