How much clearance does a boiler flue need?
Flue clearance must be at least 300mm from the ground. Terminal guards must be fitted if the flue is less than 2 metres from the ground or if a person could come into contact with the flue terminal.
How wide is a Vaillant boiler?
720 x 440 x 338
Specifications
| Technical data | Unit of measure | ecoTEC pro 28 LPG |
|---|---|---|
| Boiler type | combi | |
| Article number | 0010021838 | |
| Gas Council number | 47-044-90 | |
| Boiler dimensions (HxWxD) | mm | 720 x 440 x 338 |
How far can a boiler flue travel?
As a general rule, a flue should work effectively when it’s up to 10 metres in length. This is usually based on a standard thickness of 60/100mm. For flues that need to be longer than this, it’s a good idea to increase the thickness to 80/125mm to ensure that the gases are able to escape easily.
How far should a window flue be?
The exact distance will depend on the size of your home but, generally, the regulations prevent a boiler flue from being situated within 30-60cm of a window or door. This is to prevent harmful gases from exiting the flue and then re-entering the property through an open door or window.
Can you box in a boiler flue?
No person shall connect a gas appliance to a flue which is surrounded by an enclosure, unless that enclosure is so sealed that any spillage of products of combustion cannot pass from the enclosure to any room or internal space other than the room or internal space in which the appliance is installed.
What does code F28 mean on a Vaillant boiler?
ignition fault
The F28 code is displayed when your boiler fails three ignition attempts, resulting in the boiler halting operation and turning off. Vaillant officially defines the F28 error code as an ignition fault. Therefore, the causes of the F28 fault can be broadly categorised into either an ignition fault or a gas valve fault.
Can a boiler flue be extended?
Boiler flue extensions are used to extend a boiler’s flue outlet system, effectively an additional flue length of either horizontal or vertical orientation. Flue extensions are brand specific and must be the same brand as the manufacturer of the flue piping system that is being extended.
Does filling loop go on flow or return?
It doesn’t matter where you put it and no, it will not invalidate a warranty. If you look at vaillant ecotec plus Boilers, their built in loop is on the flow. There are thing that are better placed on the flow such as filters and expansion vessels.
How close should a boiler flue be to a window?
30cm
The regulations differ for most boiler models depending on their size, but the typical guide is that the flue needs to be at least 30cm away from an opening, such as a window, if it is to be placed above or to the side of said opening.
How big does a flue clearance have to be?
Flue clearance must be at least 300mm from the ground. Terminal guards must be fi tted if the fl ue is less than 2 metres from the ground or if a person could come into contact with the fl ue terminal. 18. 600mm distance to a surface facing a terminal, unless it will cause a nuisance.
Where to place flue duct in Vaillant boiler?
• For installations where the air/flue duct is to be installed directly to the rear of the boiler, the installation template details the position of the flue exit hole for horizontal top outlet installation. Top outlet flue exiting to side • For installations where the air/flue duct is to be installed to the side]
What are the regulations for vertical flue in a boiler?
Vertical flues must not terminate within 600 mm of an openable window, air vent or any other ventilation opening. The installation of the boiler and flue must be in accordance with the Gas Safety (Installation and Use) Regulations 1998, the Building Regulations and BS 5440 Part 1’. Two types of flue system are available for ecoTEC
How big of a clearance do you need for a boiler?
2) Dimension F: This clearance may be reduced to 25 mm without affecting the performance of the boiler. However, in order to ensure that the condensate plume does not affect adjacent surfaces, a clearance of 300 mm is preferred. For IE, recommendations are given in the current edition of IS 813.