What port is used for WOL?

What port is used for WOL?

UDP port 9
Wake-on-LAN uses UDP port 9 by default, to send WOL messages. This port is available for use on most Windows computers. However, if you have installed “Simple TCPIP services”, then Windows may be running the “discard” service.

What is Wol link speed?

In order for Wake-on-LAN to work, parts of the network interface need to stay on. This consumes a small amount of standby power, much less than normal operating power. The link speed is usually reduced to the lowest possible speed to not waste power (e.g. a Gigabit Ethernet NIC maintains only a 10 Mbit/s link).

How can I tell if WOL is working?

How do I test WOL?

1. Make a note of the MAC address, IP address, and Subnet Mask of the Network Adapter for which WOL was enabled.
2. Power the system off.
3. On a remote Windows Server 2008* system that is on the same subnet of the system to Wake Up, run a WOL utility.
4. Verify that the remote system powered on correctly.

What is the best Wol?

Here’s the Best Wake-On-LAN (WOL) Software & Tools of 2021:

• Solarwinds WOL Utility.
• ManageEngine OpUtils.
• Depicus WOL GUI.
• NirSoft WakeMeOnLan.
• Aquilatech WOL.
• MatCode MC-WOL.
• WakeUp 1.01.
• Hm Software NL Wake-On-Lan.

Do I need to port forward for WoL?

The Wake-on-LAN packet must be forwarded to every device running behind your router, and a device will only wake up if the information in the WoL packet matches it. To do this, you’ll need to forward the port to the “broadcast address,” which will broadcast the packet to all computers on a network.

How do I find my WoL port?

Open the Device Manager and expand the “Network Adapters” section. Right click on your network card and go to Properties, then click on the Advanced tab. Scroll down in the list to find “Wake on Magic Packet” and change the Value to “Enabled.” You can leave the other “Wake on” settings alone.

Can LogMeIn wake up a sleeping computer?

Open the LogMeIn Control Panel and navigate to Options > Preferences > Advanced Settings. Under Wake On LAN, select Enable ‘Wake On LAN’ from sleep and power off.

Is SolarWinds WOL safe?

This process is simple and safe, as it does not expose any ports to the Internet. To wake up a device, Wake-on-LAN (WOL) technology uses a specific network package containing the MAC address of the destination network card. This packet is broadcast to all computers in the network.

What is Fusion WOL?

Using Fusion WOL (Wake On Lan) you can take advantage of turning on a remote PC throw the net interface. The utilities that this software brings are mainly turning on a remote PC using its IP Address, if it was previously stored at the cache, otherwise you should write the MAC address of the remote PC.

What’s the default WOL speed on an Intel Nic?

The default is 10Mb, and this causes issues with certain multicast tasks. Broadcom NICs have a “WOLSPEED” setting on the driver – but I cant see an option for anything similar on my Intel NICs. 04-13-2010 03:55 AM Is there anywhere I can post a feature request? 04-13-2010 08:22 AM Consider your request received. Thank you for the suggestion.

How to enable Wake on LAN ( WOL ) in Windows?

Open the Device Manager, click Network adapters, right-click the Network Adapter to be WOL enabled, and click Properties. Click the Link Speed tab then verify installation of Intel® PROSet/Wireless Software and verify it is the latest version. Click the Power Management tab and mark the Wake on Magic Packet from power off state check box.

Can a WOL be used on a WAN network?

Although the original design of the WOL (Wake on LAN) network is used in the LAN environment, we can also try to use the Wake On Wan network in the WAN (that is, the Internet). In this way, it is much more convenient for the company to wake up the computer at home. The WAN WOL needs to be configured on the router.

How to enable Wake on pattern match ( WOL ) on Windows 10?

Use the “Value” drop-down menu and select the Enabled option. (Optional) Select the Wake on pattern match option. Use the “Value” drop-down menu and select the Enabled option. (Optional) Select the WoL & Shutdown Link Speed option. Use the “Value” drop-down menu and select the 10Mbps option.