How do you zone a Brocade switch in CLI?

How do you zone a Brocade switch in CLI?

How to create zones from CLI on a Brocade SAN Switch

1. admin> switchshow.
2. Note:Any devices that connect using NPIV use nsshow command to find the WWPN addresses logged in to the port.
3. 2.Run the cfgshowcommand.
4. admin> cfgshow.
5. cfgshow will display the configuration and how the zoning is currently configured.

How do I reset my Brocade switch CLI?

To reboot the CP and execute the normal power-on booting sequence, perform the following steps.

1. Open the Switch Administration window as described in. Opening the Switch Administration window. on page 52.
2. Click Reboot.
3. On the Reboot Confirmation window, click Yes to continue.
4. Click Apply.

How do I check my port on my Brocade switch?

To do so, run the licensePort –reserve command. Run the portShow command to ensure the port is licensed. We see the port is licensed, but still disabled.

How do I turn on the port on my Brocade switch?

To enable a port:

1. Connect to the switch and log in as admin as described in Connect to the Command Line Interface.
2. Issue the portenable portnumber command, where portnumber is the number of the port you want to enable.

What is SAN zoning?

Zoning in a SAN is a used to segment traffic between targets and initiators, or less formally workstations and storage. Zoning can be set up through software, referred to as Soft Zoning or it can be set up through hardware, referred to as Hard Zoning.

How do I enable zoning on my Brocade switch?

The basic steps to creating a zone on a Brocade switch are:

1. Create aliases (optional, makes device management easier to read and administer) – alicreate.
2. Create the zone – zonecreate.
3. Create the zone configuration – cfgcreate.
4. Enable the configuration – cfgenable.
5. Save the configuration – cfgsave.

How do I set my Brocade switch to factory settings?

Tap the “Enter” key a few times and the Brocade command prompt will display. Type the console password if requested and press the “Enter” key. Type “configDefault” and press the “Enter” key. The switch configuration is now reset to factory default settings.

How do I know what model SAN switch I have?

Brocade switch models can be identified by running the switchshow command, or through the use of the Brocade serial number.

What is DPOD Brocade?

Dynamic Ports on Demand (DPOD) does not require any predefined ports for assignment. The POD feature automatically assigns POD licenses from a pool of available licenses.

What is ISL port?

An ISL is a connection between two switches through an Expansion Port (E_Port). ISL Trunking simplifies network design and reduces the cost of storage management by optimizing bandwidth utilization and enabling load balancing of traffic at the frame-level.

How do you make an ISL in a Brocade switch?

1. Configure the port speed: portcfgspeed port-numberspeed.
2. Configure the trunking mode for each ISL:
3. Enable QoS traffic for each of the ISL ports:
4. Verify the settings:
5. Calculate the ISL distance.
6. Set the distance on each ISL port:
7. Verify the distance setting:
8. Verify that both switches form one fabric:

What are the Brocade SAN switch CLI commands?

The list of Brocade SAN Switch CLI commands () aaaconfig Configure RADIUS for AAA services ad Specifies all administration domain (AD)-level operations ag Configure the Access Gateway feature agautomapbalance Configure the Access Gateway automapbalance feature agshow Displays the Access Gateway information registered with

How to zone a brocade switch in Java?

Zoning Your Brocade Switches using CLI – Step by Step (when java just won’t work) 1 Backup the Switch Configuration 2 Create Aliases 3 Create Zones 4 Add Zones to a New or Existing Zone Configuration 5 Save the Config 6 Enable the New/Updated Zone Configuration More

What happens when a test fails in brocade?

If the tests fail, an error message is displayed and the configuration is not saved. This command ends and commits the current transaction. If a transaction is open on a different switch in the fabric when this command is run, the transaction on the other switch is automatically aborted.

What does recovory do in Brocade Fabric OS?

Recovory (Downloads configuration data to the system.) Sets the switch name. Displays switch and port status. Displays status and configuration parameters for ports and GbE ports. Enables a port or a range of ports.