How do I use offset list in EIGRP?
To add an offset to incoming and outgoing metrics to routes learned via EIGRP or RIP, use the offset-list {access-list-number | access-list-name} {in | out} offset [interface-type interface-number] router configuration command, as explained in Table 5-2.
What is distribute list in EIGRP?
Redistributes all EIGRP networks into OSPF. Creates an outbound distribute list to filter routes being redistributed from EIGRP into OSPF. NOTE: The implicit “deny any” state-ment at the end of the access list pre-vents routing updates about any other network from being advertised.
What is RIP offset list?
RIP offset lists allow RIP to add to a route’s metric, either before sending an update, or for routes „ received in an update. The offset list refers to an ACL (standard, extended, or named) to match the routes; any matched routes have the specified offset, or extra metric, added to their metrics.
How do I set administrative distance in EIGRP?
The lower the better…as you can see EIGRP has a lower administrative distance (90) than OSPF (110) so we will use EIGRP in my example. Keep in mind: The administrative distance is only local and can be different for each router….How to configure Administrative Distance.
| Source | Administrative Distance |
|---|---|
| EIGRP summary | 5 |
| External BGP | 20 |
| EIGRP | 90 |
| IGRP | 100 |
How do I use distribute list in EIGRP?
Go to the configuration of the EIGRP process and use the distribute-list command to see your options. As you can see we can choose between an access-list, a prefix-list or a route-map. Let’s start with the access-list. You are probably familiar with the concept of access-lists if you studied CCNA.
What is distribute list?
A distribute-list is used to control routing updates either coming TO your router or leaving FROM your router. Distribute-lists work on a variety of different IOS routing protocols. Because of that, learning how to use distribute-lists is very valuable.
How do I configure RIP routing protocol?
Configuring RIP requires the following steps:
- Step 1 Enable the RIP routing process, which places you in router configuration mode via the Router#router rip command.
- Step 2 Specify those networks that should be advertised using RIP via the Router(config-router)#network [network-number] command.
Which is the correct command for EIGRP configuration?
Router(config)# router eigrp autonomous_system_# This command will enable EIGRP routing protocol in router. We can use any ASN (Autonomous System Number) from 1 to 65,535. In order to become EIGRP neighbors this number must be same on all participates.
Which is the correct command for EIGRP configuration *?
To configure an EIGRP interface as passive, you use the command passive-interface interface-id under the EIGRP process for classic configuration.
When to use an offset list in EIGRP?
In certain situations an engineer may need to manipulate EIGRP metrics, and one method is to use Offset Lists to increase both the AD (Advertised Distance) and FD (Feasible Distance) of a route by a certain value – the offset. Offset List configurations define the following: route(s) that we want to amend the metric for (matching an ACL)
How is distribute list introduced in EIGRP 1?
Now , in the Routing Protocol (EIGRP 1) , a Distribute List is introduced which calls Access List 1 for incoming traffic over Fa0/0. Once Distribute List is configured , we see that subnet “ 1.1.1.2/32 ” is not received on R2 any more.
When to use the offset list in Rip?
The offset-list lets you increase the metric when you send a routing update to your neighbor or when you receive it. You can use this for RIP or EIGRP, it is not supported for OSPF. Let me show you an example to see what I mean: We have two routers running RIP version 2.
When to use the offset list in OSPF?
The offset-list lets you increase the metric when you send a routing update to your neighbor or when you receive it. You can use this for RIP or EIGRP, it is not supported for OSPF.