How do I program my directv RC73 remote to my directv box?

How do I program my directv RC73 remote to my directv box?

How To Program DIRECTV Remote RC73

1. Press select and then the mute button – you will see a green LED light flash twice on the remote.
2. Dial the following number, “961” and then press the channel button UP – you will be able to change your channels on the TV.
3. Press volume button Up and Down – Program Remote option pops up.

How do I resync my directv remote to my receiver?

Make sure your remote is paired with your receiver.

1. Point the remote at your Genie, Genie Mini, or Wireless Genie Mini.
2. Press and hold MUTE and ENTER at the same time on your remote.
3. The screen displays Applying IR/RF Setup. The remote is synced.

How do you program a RC71 remote?

Here’s how to follow the steps you’ll need!

1. Start by pressing the {MENU} button on your remote, then arrow down to “Settings” and press {SELECT}.
2. Arrow down to “Remote Control” and press {SELECT}.
3. Arrow down to “Program TV” and press {SELECT}.
4. Now here, find the model of your TV, highlight it and press {SELECT}.

How do I sync directv Genies?

Pair the Wireless Genie Mini with your Genie HD DVR

1. Press MENU on your Genie remote.
2. Select Settings > Whole-Home > Manage Client > Add Clients.
3. Write down the PIN you see on the screen.
4. Go back to the TV where you connected the Wireless Genie Mini.
5. Use the remote to select Continue and enter the PIN when prompted.

Where is the mode switch on DirecTV remote rc73?

Find the MODE switch at the top of the remote, and slide it over to TV. Press and hold the MUTE and SELECT buttons at the same time until a green light flashes twice from the top of your remote. Punch in the numbers 960, which should prompt the green light to flash twice again.

How do I reset my directv Genie Mini?

Unplug your receiver

1. Unplug your receiver’s power cord from the electrical outlet, wait 15 seconds, and plug it back in.
2. Press the Power button on the front panel of your receiver. Wait for your receiver to reboot.

How do I program my RC71 remote to my genie receiver?

First, have your Genie Mini receiver connected and powered on. Next, grab your RC71 remote and simultaneously hold the “MUTE” + “ENTER” buttons until you see a box appear on your TV screen that says “Applying IR/RF Setup. Please Wait” (this appears after about 5 seconds of holding those buttons).

What is the difference between RC71 and RC73?

There is one, and precisely one, difference between previous DIRECTV Genie Remotes and the RC73: the RC73 will control the 2015 LG DIRECTV-Ready TVs. The RC72 remote did improve on the RC71 by adding a few new codes and fixing certain issues with lower-priced TVs but the RC73 doesn’t have any those additional changes.

How does directv genie work wirelessly?

The DIRECTV wireless Genie uses radio signals, similar to a cellphone transmission except that the signals carry digital TV data instead of voice data. The Genie and Wireless Video Bridge require professional installation, but installing additional wireless Minis is easy enough to do it yourself.

Why won’t my mini genie connect?

Make sure the HDMI connection to the TV is secure. Check that the TV input selection. Try changing the channels. Press and hold the red reset button located near the access card to reboot the system.

How to turn on GEnie on Direct TV?

Press and hold the MUTE and SELECT buttons while continuing to point the remote at a Genie device. Stop when the green light at the top of the remote blinks twice. Use the buttons on your Genie remote to enter code 961. Press the channel up button once.

What kind of remote control do I need for DirecTV?

The new DIRECTV RC71, RC71B, RC72 and RC73 Genie RF Remote Controls are factory-set to Infrared (IR) Mode, so they can work with your earlier model receivers. To make your remote control other devices (e.g., your TV) follow these steps:

Is there a way to program a Genie remote?

Below is the most common way to program a Genie remote. If these steps don’t work for you, follow the next set of steps to program a remote manually. Point the remote at your Genie HD DVR, Genie Mini, or Wireless Genie Mini. Press and hold the MUTE and ENTER buttons. Stop when the green light at the top of the remote blinks twice.

How to deactivate RF transmitter on DirecTV remote control?

To deactivate the RF Transmitter on the DIRECTV remote control, perform the following steps: Step 1: Press and hold “MUTE” and “SELECT” at the same time until the green light flashes twice. Step 2: Enter 9 6 1. Step 3: Press and release “Channel Down”.