Why is my bow shooting inconsistent?
Many archers have a tendency to grip their bow too tightly. When you place your bow hand on the side of the bow handle, you’re forced to completely circle your fingers around it to tightly maintain your grip. This also torques the bow at an angle, resulting in inaccurate and inconsistent arrow flight paths.
Why are my arrows spiraling?
shooting field points with arrows that have any kind of offset or helical fletching will result true-flying arrows beyond 25-30 yards. Any arrows that are corkscrewing beyond 30 yards are either miss-fletched, or are in a cross wind. Proper fletching will straighten out form flaws and tuning flaws beyond 30 yards.
How do you adjust the draw weight on a Mathews Creed?
Draw weight adjustments are made using either a 3/16” or 7/32” Allen Wrench. Turn the limb bolt clockwise to increase the draw weight and counter clockwise to decrease the weight. Both limb bolts must be adjusted equally, or the bow may become out of tune/synchronization. The limb bolt should be snug.
Is the Mathews Creed a good bow?
This bow delivers in all areas. It’s accurate, church-mouse quiet, vibration free, and a dream to draw and shoot. When it comes to reaching full draw on the Creed, I think everyone will find it amazing that a bow spitting arrows at 328 fps IBO can be this smooth to haul back.
Why are my arrows not grouping?
Arrow-Rest Contact Fletchings are often the culprit when it comes to arrow contact. If you notice unusual wear on one of your fletchings, it’s likely hitting the rest. Clean your rest thoroughly and then spray your fletchings with foot powder. After a shot, check your rest to see if any powder is on it.
Why do my arrows fly sideways?
When we release the string it will inevitably move sideways around the fingers so the arrow is never being pushed directly forward, this lateral movement, length of the arrow, and weight of the tip causes the arrow to compress and bend as the rear accelerates faster than the tip can.
Can you adjust draw length on Mathews Creed?
Remove the setscrews in the cams with a screwdriver. You do not need to release tension from the bow limbs, string or cables to change the draw length with adjustable cams. Rotate the adjustment wheels on the cam, one mark up to increase draw length or one mark down to decrease draw length.
How fast is a Mathews Creed?
Mathews Creed vs. Mathews Heli-m
| Bow | Mathews Creed | Mathews Heli-m |
|---|---|---|
| AtA Length | 30 “ | 30 “ |
| Draw Length | 26.5 ” – 29.5 “ | 26 ” – 30 “ |
| Draw Weight | 50 lbs – 70 lbs | 40 lbs – 70 lbs |
| IBO Speed | 328 fps | 332 fps |
What is a Mathews creed worth?
Sporting a forgiving 7-inch brace height, decent speeds up to 328 feet per second, and virtually no hand shock, the Creed is sure to be the bow of choice for many shooters despite the $999 price tag.
Why are my broadheads not grouping?
If your broadhead tipped arrows are not grouping with your field points, the first thing to check should be your cam timing. This is due to either the top or bottom cam being faster than the other, causing the arrow to not fly out of the bow straight. Checking cam timing is best done by way of a draw board.
What makes the Mathews Creed bow so special?
Mathews’ new flagship bow is the result of 2 decades worth of innovation and technology wrapped up in one sweet shooting package. The Mathews Creed was built using a synergistic approach; meaning different components of the bow have been brought together from other bows to create an enhanced effect.
Can a Mathews Bow tune out of the box?
In reality, the top hat system is a genius, relatively simple system to help you find the best possible tune for your bow. Your Mathews bow is likely to tune out of the box with minimal adjustment, provided you have a proper grip, the rest is set to the right-center shot and height and your nocking point is close.
Why is the gripper motor on my Wurlitzer so slow?
When the gripper arm motor is too slow it can be either lubrication or a fouled up armature inside the motor itself. Here are some pictures on fixing the armature by cleaning the gaps with a thin metal strip (or plastic) that fits snuggly in the slots of the armature. Cleaning these will bring the motor back to factory speed.
When to move the rest to the left on a Mathews Bow?
First, you can move your rest to the right in very small increments to see if it cleans it up. If you can’t clean it up without moving the rest too close to the riser (right-handed shooter), then it’s time to move to the top hat system. If you are getting a left tear, then the cam needs to move to the left.