How configure EIGRP IPv6 on Cisco router?

How configure EIGRP IPv6 on Cisco router?

Configure the EIGRP for the IPv6 routing:

1. Enable the IPv6 routing on a router.
2. Assign the router ID of the each router.
3. Enable the EIGRP for IPv6 routing on every router.
4. Configure the EIGRP for IPv6 by using the AS 1 on a gigabit Ethernet and serial interfaces on a router.
5. Determine a neighbor adjacency.

Which commands create an EIGRP routing process in IPv6 for as 200 on router r2?

Create an EIGRPv6 process using ipv6 router eigrp asn command. Assign an EIGRPv6 router ID using the eigrp router-id router-id command in router configuration mode. Enable EIGRPv6 on interfaces using the ipv6 eigrp asn command in interface configuration mode.

Does EIGRP work with IPv6?

EIGRP for IPv6 uses multicast like EIGRP (for IPv4) to communicate between local EIGRP neighbors; the multicast address used is referred to as the All EIGRP routers address of FF02::10 (very similar to the previous 224.0. 0.10).

Which IPv6 command is required to be the first command executed on a router when configuring EIGRP?

ipv6 unicast-routing global configuration command
Enable IPv6 routing on a Cisco router using the ipv6 unicast-routing global configuration command. This command globally enables IPv6 and must be the first command executed on the router. Configure the IPv6 global unicast address on an interface using the ipv6 address address/prefix-length [eui-64] command.

What is the EIGRP IPv6 multicast address?

Notable IPv6 multicast addresses

Address	Description
ff02::8	IS-IS for IPv6 routers
ff02::9	RIP routers
ff02::a	EIGRP routers
ff02::d	PIM routers

What is the difference between EIGRP IPv4 and IPv6?

EIGRP for IPv6 advertises IPv6 prefixes/lengths, rather than IPv4 subnet/mask information. EIGRP for IPv6 uses the neighbor’s link-local address as the next-hop IP address; EIGRP for IPv4 has no equivalent concept.

Which address will EIGRP for IPv6 use as the router ID?

Which address will EIGRP for IPv6 use as the router ID? EIGRP for IPv6 uses the same router ID as EIGRP for IPv4 uses. The 32-bit number can be configured with the router-id command or automatically assigned from the highest IPv4 address on an enabled interface.

What is IPv6 EIGRP?

It is an enhanced distance vector protocol that relies on the Diffused Update Algorithm (DUAL) to calculate the shortest path to a destination within a network. EIGRP for IPv6 works in the same way as EIGRP IPv4 where they can be configured and managed separately.

How do I configure IPv6?

In Settings go to Network & Internet and click the Properties button for the interface you wish to configure. Click the Edit button under IP settings, change the configuration type to Manual, enable IPv6, and populate your settings.

How do I enable IPv6 on my router?

This Article Applies to:

1. Log in to the web-based interface of the router.
2. Go to Advanced > IPv6.
3. Enable IPv6 and select the internet connection type provided by your ISP.
4. Fill in information as required by different connection types.
5. Configure LAN ports.

What are the two rules of IPv6 compression?

Rule 1: When there are continuous zeros (0s) in the IPv6 address notation, they are replaced with ::. This rule is also known as zero compression. Rule 2: Leading zeros (0s) in the 16 bits field can be removed. But each block in which you do this, have at least one number remaining.

What are 224 IP addresses?

224.0. 0.22 is a multicast-address. Multicast is thought for ip addresses which can be “subscribed” to. A multicast IP can be subscribed to by multiple network interfaces and will be routed by routers in a special way.

What is the EIGRP command in IPv6?

The ipv6 summary-address eigrp command is used to configure interface-level address summarization. EIGRP for IPv6 summary routes are given an administrative distance value of 5. The administrative distance metric is used to advertise a summary address without installing it in the routing table.

Where does the EIGRP global configuration command set up?

In the following example, the router eigrp global configuration command sets up EIGRP routing in autonomous system number 109. The network router configuration commands specify EIGRP routing on networks 192.168.7.0 and 172.16.0.0.

How to configure an interior gateway routing protocol ( EIGRP )?

To configure the autonomous-system number for an Enhanced Interior Gateway Routing Protocol (EIGRP) routing process to run within a VPN routing and forwarding (VRF) instance, use the autonomous-system command in address-family configuration mode.

What does EIGRP mean on a Cisco NCS 6000?

This module describes the commands used to configure and monitor the Enhanced Interior Gateway Routing Protocol (EIGRP). For detailed information about EIGRP concepts, configuration tasks, and examples, see Implementing EIGRP on in Routing Configuration Guide for Cisco NCS 6000 Series Routers .