Do you need a MOSFET for airsoft?
When specifically discussing airsoft uses, mosfets are used for diverting the electrical current away from the trigger contacts. When installed into the wiring of an airsoft gun, the mosfet redirects the current from the battery to go straight to the motor without going through the trigger contacts first.
What is a programmable MOSFET?
Multifunction programmable 3rd generation MOSFET. The system has as many as 10 functions. The system allows for the lossless rate of fire adjustment; it protects state-of-the-art Li-Ion batteries: LiPoly and LiFePO4; it has a built-in active brake; it protects contacts against damage.
What is active braking airsoft?
– Active braking uses the excess energy from the motor to stop it. The braking effect is the most powerful with high torgue motor. – 6 wires connection.
Are MOSFETs waterproof?
It is waterproofed in two ways: a silicone conformal coating around the MOSFET and an adhesive heatshrink seals it. Warranty only covers damage to the MOSFET; it does not cover damage to the wire or other parts of unit.
What is an airsoft electronic trigger?
So, trigger response is primarily used when talking about AEGs (electric airsoft guns), not gas or “springer” guns. The trigger response of an AEG is determined by the speed at which the internal gearbox can pull back a spring and piston, and let it fall to propel a BB.
What does the Krytac Mosfet do?
The KRYTAC MOSFET Assembly is designed to fit inside the TRIDENT Mechbox to regulate battery current and protect trigger contacts. This is a basic MOSFET that is designed to prevent arcing between the trigger terminals.
What is an ETU Airsoft?
ETU++ is a dedicated replacement for G&G ETU electronic board. It enhances your trigger unit by adding many new, useful features. The stock trigger unit (switch set) is retained, so there is no need to open the gearbox. Works with any G&G ETU replica, as well as 7.4V, 11.1V and 14.8V batteries.
What is Active Brake mosfet?
Professionally made mosfet with motor active braking designed for airsoft electric guns (AEG). Device increases gun rate of fire and battery holds longer, than with basic wiring. Active break solves multiple shots in semi mode with weapons with very high rate of fire (ROF).
What is active breaking AEG?
The NanoAAB is the highest quality MOSFET with Active Brake. The second function – active brake, stops the motor immediately after releasing the trigger. It makes rising of realism and increasing gearbox lifespan. The circuit is compatible with all the replicas, also the tuned ones.
Can a MOSFET pair be used for a SPDT switch?
With an n- and p-channel MOSFET, you can easily implement a single-pole double-throw (SPDT) switch to isolate part of a circuit and power it from a secondary supply for standby operation while the rest of the circuit is off ( Figure 1 ). By using a complementary pair, you can use a single control input for the MOSFETs.
When does the p channel MOSFET go on?
The switch isolates part of a circuit and powers it from a secondary supply during stand-by operation when the rest of the circuit is off (b). When the 2N7002 or similar control MOSFET ties the gates together and pulls them to ground, the p-channel MOSFET is on.
Is the single pole SPDT switch MBB or SPDT?
According to the way of operating, the single pole double throw switch can be divided into BBM type SPDT switch ( break-before-make) and MBB type SPDT switch ( make-before-break ). By default, the pole of the BBM SPDT switch is connected to NC throw circuit and disconnected from the NO throw circuit.
What happens if the SPDT switch is switched off?
For example, a SPDT switch is connected to Device A and Device B, the Device A will be on status and the Device B is shut down if the SPDT switch is switched off; conversely, if the SPDT switch is switched on, the Device A will be off status and the Device B will be turned on.