Why is my DStv decoder not working?

Why is my DStv decoder not working?

The reason your DStv says no signal is because there is an error in the DStv installation. This is caused by either a misaligned satellite dish, a faulty LNB, an improperly connected F-connector plug, loose cables or incorrect decoder settings on the LNB type.

What to do if DStv is not scanning?

Please try performing a hard reboot on the decoder by following these steps: Unplug the decoder from the wall> Unscrew the LNB cable> Remove the smartcard (if the decoder has no smartcard, skip this step). After a few seconds, put everything back in its place and wait for the decoder to scan.

How do I connect my DStv decoder DSD 3 u to my TV?

Connect any one of the four cables from the satellite dish directly to the LNB input on the back of the decoder. 1. If you have a HD TV, use the supplied HDMI cable and connect it to the HDMI port (marked 1) on the back of the decoder, then connect the other end to the HDMI port on the TV.

Why does my DStv decoder keep rebooting?

The main cause of the DStv Explora 2A keeps rebooting problem is a damaged DStv software. Often, Multichoice releases new decoder systems, and you can download them when you connect your decoder to the internet.

How do I fix my decoder signal?

What to do when your decoder loses signal

1. Step 1: Check whether the cables connecting the decoder are in place.
2. Step 2: Try rebooting the decoder.
3. Step 3: Visually check your dish.
4. Step 4: Examine the status of the Low-noise Block downconverter (LNB)

Why is my DStv stuck on scan?

So the power has just come back on and your decoder is stuck scanning for picture, before you call give this a try: switch it off at the wall wait 10 minutes and power up again your decoder will start up and your viewing should restart. If you get an error you can clear it using one of our Self Service platforms.

What causes installation wizard?

The DStv installation wizard is a setup assistant that lets you choose your decoder settings and connect to the satellite. The wizard starts automatically when you switch your decoder for the first time. You can also see the wizard if you reset your decoder.

How do I clear my DStv installation wizard?

All you need is your remote, as you can easily do it by pressing the “Exit” button on the remote. It will immediately get rid of the installation wizard. You can also get rid of the installation wizard by pressing the “Back” button severally.

Can you trade in your old DStv decoder?

You will keep accessing DStv for as long as your older Single View decoder is still working. You can, however, trade-in your active Single View decoder at any of our service centres or agencies for a brand new DStv HD Decoder for only R349.

How do I fix a corrupted DStv hard drive?

Insert the power cable, and don’t let go of the power button as your decoder powers up. It will bring up the word “CODE,” and to repair the corruption, press P-P+P-P+ on your remote. It will begin to format all the data on your decoder, and when it is done, it will reboot itself.

How do I update my DStv software?

You can manually update the software as follows :

1. Press the blue DStv button.
2. Go to Settings.
3. Select User Preferences.
4. Select General.
5. Select Download latest software.
6. (If this option is greyed out, the decoder is already on the latest software)

What kind of decoder do I need for DStv?

The DStv decoder model SD PVR Dual View can record and play back recorded Satellite TV channel programs, at the convenience of the DStv subscriber. Simultaneously, one can b viewing one channel, while recording another channel on the TV 2 platform of the DStv SD PVR decoder model. ALL DSTV DECODER MODEL – DSD 1131

Is the DSD 910 still in use as a decoder?

The DStv decoder model DSD 910 is now a Legacy decoder – no longer in use. This DStv decoder model as seen in fig 2 above followed the DSD 910 model of the DStv. It is very similar to the DSD 910 in features, functions and applications.

How to fix DStv decoder loading Wizard error?

Just like that of loading problems, you can solve DStv decoder installation wizard error and channels scanning problems by factory resetting your decoder using the P+ and P- buttons. lookout for the word “ CODE ” on your TV and once you see it, release the P+ button

Is the DSD 1110 still in use till date?

More importantly, the DStv Extra-View (Xtraview) became possible with the coming of the DSD 1110. Surprisingly, the DStv decoder model DSD 1110 is still in use till date. DStv decoder model DSD 1110 enjoys automatic DStv software upgrade technology, which is why it is still in use till date.