How does Stalker Dual radar work?
The Stalker DUAL compensates for patrol speed variations when generating the Doppler audio. Since the audio tones do not vary with patrol speed, the operator learns to correlate this true Doppler audio with target speed, which eliminates the need to constantly watch the display to determine target speed.
What does XMIT mean on radar?
XMIT/HLD toggles between transmit mode and hold mode. SS: SS is the Start/Stop control for stopwatch operation. STA/MOV: STA/MOV selects either stationary mode or moving mode.
What is a stalker DUAL DSR?
The Stalker DSR allows tracking both patrol speed and target speeds after lock using three colors (amber, red, and green) to differentiate between the strongest, faster and patrol speeds. No longer does the operator need to tell the radar if same-direction traffic is faster or slower than the patrol vehicle.
Can the police radar be wrong?
A radar cannot identify the specific vehicle responsible for speeding. As a result, an officer may accidentally clock the speed of the vehicle next to the target vehicle. If lidar radar is pointed at the wrong surface or officer moves, it can cause inaccurate readings.
How do you test a radar stalker?
A radar should be tested with tuning forks on a daily basis….Same-Lane mode
- Strike both forks.
- Put the FASTER (smaller) fork in front of the antenna.
- Radar should read faster fork as PATROL SPEED.
- Put the SLOWER (Larger) fork in front of the antenna.
- Radar should read the SUM of the fork speeds.
How do you reset a Stalker radar gun?
Press and hold the MENU key for longer than ½ second to enter the Options Menu. Step 3. Using the MENU key, scroll through the menu to RESET.
What is the margin of error on a radar gun?
An officer’s visual estimate of speed will be less accurate than a laser device and as such the margin of error will be greater. Depending on what an officer says in court, the margin of error for a visual estimate could be anything from +/- 5 km/h to +/- 10 km/h.
How are police radars calibrated?
According to the operations manuals that come with police radar, to ensure accuracy, every radar unit is supposed to be calibrated with tuning forks before each and every working shift and also before and after being used to detect each speeding violation. Radar units often have an internal calibration function.
How do you trick a speed gun?
When the officer sees a car up ahead that they want to measure the speed of, they take their radar gun out of hold and tell it to transmit, a technique known as “instant on” or I/O. The trick to countering instant on is to to have 1) a very sensitive radar detector and 2) a rabbit up ahead of you.
What to say when a cop asks how fast you were going?
Keep It Simple The officer might ask “Do you know why I stopped you?” If you answer at all, your answer should always be “No.” Similarly, if the officer asks “Do you know how fast you were going?,” the best answer is “Yes.” The officer may then tell you how fast you were going but do not argue.
Where can I get the stalker moving police radar operator’s manual?
Moving Police Radar Operator’s Manual applied concepts, inc. 2609 Technology Drive Toll Free Sales 1-800-STALKER Plano, TX 75074 Toll Free Service 1-877-STALKER Phone (972) 398-3780 [email protected] Fax (972) 398-3781 www.stalkerradar.com 011-0004-00 Rev F Table of Contents Previous Page Next Page 1 2 3 4 5
What is the PWR switch on a stalker?
The PWR switch is the main On/Off power switch. S PWR: has a jumper in its DUAL DSR power-supply circuit that selects one of the two following options: 1. When vehicle power is applied, the unit must be turned on by pressing the PWR switch. Page 8: Voice Enunciators
What do I need to know about dual DSR?
DUAL DSR Target Doppler Audio – The key is used to adjust the volume of the Target Doppler audio up or down. Press the key t make the display step through: Aud 1, Aud 2, Aud 3, and Aud 4. Page 9: Ergonomic Remote Control Functions
What is the target Doppler key on dual DSR?
DUAL DSR Target Doppler Audio – The key is used to adjust the volume of the Target Doppler audio up or down. Press the key t make the display step through: Aud 1, Aud 2, Aud 3, and Aud 4.