What does cable Select mean on jumper settings?

What does cable Select mean on jumper settings?

Cable select, also referred to by the acronym CS, is a disk drive jumper setting which automatically sets the priority of a disk drive by its position on its data cable. When cable select is enabled, the drive configures itself as a primary or secondary depending on its position in the drive chain.

How do you use a jumper hard drive?

Four-Pin Seagate SATA Drives

  1. Locate the jumper block on the back of the Seagate SATA hard drive.
  2. Place the jumper over the first and second pin on the right to limit the drive’s data transfer to 1.5 Gigabits per second when it is being used in a server or multi-drive desktop with slow hard drives.

Is there a jumper on the optical drive What is the jumper setting?

You may have pins on the back of your hard drive that nothing is connected to. These pins are called jumpers, and are used to enable specific types of settings. The settings these jumpers enable are hard-coded onto a drive’s programmed printed circuit board.

What is jumper HDD?

You may have pins on the back of your hard drive that nothing is connected to. These pins are called jumpers, and are used to enable specific types of settings. You enable particular settings by placing a jumper shunt onto specific pins—creating an electrical circuit between them.

What are jumper clothes?

A jumper is a long-sleeved item worn on the top half of your body, and like a sweater, is usually considered knitted or crocheted, but also seen made of jersey fabric or cotton too. Jumpers and sweaters can usually be dressed up or down, depending on the fabric and style of the design.

What is CS Cable?

CS & CV Cables Two types of cables with M12 connectors are avilable: CS (unshielded) and CV (shielded). Shielded cables are needed with SE series safety light curtains.

What is SATA cable?

What are SATA Cables? Serial Advanced Technology Attachment (SATA) or Serial ATA cables are used to connect devices in computer cable assemblies, such as storage devices, for example. The SATA technology itself is a connecter interface primarily used for computer bus connections in storage applications.

What is a jumper block?

In a computer, a jumper is a pair of prongs that are electrical contact points set into the computer motherboard or an adapter card . When you set a jumper, you place a plug on the prongs that completes a contact. A group of jumpers is sometimes called a jumper block .

What does the jumper block allow you to do?

More properly called a jumper block, a jumper is a small plastic block with embedded metal contacts that may be used to bridge two pins to form an electrical connection. When a jumper block bridges two pins, that connection is called on, closed, shorted, or enabled.

How do I check my jumper settings on my hard drive?

To find out precisely what the jumper pins do on your hard drive, just search “jumper pins” along with the model number and manufacturer of your drive. You’ll find the relevant support site that tells you which ones to use. Western Digital’s instructions for jumper pin settings on some SATA hard drives.

How do I check jumper settings on my hard drive?

What’s the jumper setting on a Maxtor drive?

Maxtor (and Quantum) drives follow the jumper configuration noted below: The drive is configured at the factory for a cable select setting. This allows the drive to assume the proper role of master or slave based on the connector used on the cable (see the UltraATA cable figure above ).

What should the jumper settings be for Seagate?

Master or single drive. If you are installing your Seagate hard drive as the only drive in the system or if it will be the primary boot drive for the system, the jumper should be set as Cable Select.

How do I jumper a Seagate Maxtor ATA drive?

If you are connecting the drive to an older system that has a pre-UDMA Mode 3 ATA controller, or you are connecting this to a cable with a slave device that doesn’t have a cable select jumper setting, jumper the drive as Master instead by putting a jumper on the first vertical set of pins closest to the data cable.

Begin typing your search term above and press enter to search. Press ESC to cancel.

Back To Top