What is the purpose of a pogo pin connector?
A Pogo pin is a device used in electronics to establish a connection between two printed circuit boards. The pogo pin usually takes the form of a slender cylinder containing two sharp, spring-loaded pins.
How are pogo pins mounted?
Pogo Pins can be mounted via a cable on the PCB. For this purpose, the Pogo Pin gets a small solder cup at the back of the pin which is used to attach a cable. CCP can supply single pins or whole connectors with preassembled cables.
How reliable are pogo pins?
In conclusion, my data shows that individual pogo pins seem to have approximately 2.4% chance of not mating correctly with their test points. When they do contact correctly, they usually show a reasonably low resistance of approximately 100 mΩ between the pin and the test pad, with worst cases being less than 500 mΩ.
What is pogo pin charger?
This is a portable charging cable with the magnetic design that it can be easily attached to any laptop, wall charger or car usb port and offers convenient and safe charging. …
Are pogo pins magnetic?
With a magnetic pogo pin, it is very easy to connect. The pin is a new standard. The strip is made of imported highquality flexible magnetic materials, with strong magnetism, high temperature resistance and long service life. And pin, waterproof joint connection.
What is spring-loaded connector?
Spring-Loaded pins, sometimes called Spring-Loaded Contacts, Spring probes, or Pogo Pins, provide a highly-reliable, precision made interconnect solution ideal for a number of demanding application requirements in the fast moving world of electronic interconnects.
What is a test pin?
A Test Land, also referred to as a Test Pin or Test Point, is a point used for board electrical tests. Create Test Points using a component, and then place them at arbitrary locations on both schematic drawings and PCB drawings. …
What are pogo pins made of?
The plunger and barrel of pogo pins usually use brass or copper as a base material on which a thin layer of nickel is applied. As common in electrical connectors, manufacturers often apply a gold plating that improves the durability and contact resistance. The springs are usually made of copper alloys or spring steel.
How do I remove pogo pin?
In order to remove the spring-loaded contact pin (pogo pin), you need to use a set of needle nose pliers. Use care when squeezing the pin as you do not want to damage it. However, you must it securely. Hold the pogo pin firmly with the pliers, and pull it straight out from the TDR probe.
Are pogo pins waterproof?
Environmental Protection. Like most connectors rated for use in portable and wearable medical equipment, pogo-pin connectors can provide IP-rated protection against ingress of fluids. In spring-loaded connectors, this waterproofing is achieved by installing an O-ring between the contact pin and housing.
How does a pogo pin for a connector work?
Different pogo designs maximize the stability of the current flow by increasing the number of contact points inside the pin. Pogo pins are produced with high precision turning machines and don’t require a mold as it is the case for other connectors that are using a stamping process.
Which is better a spring pin or a pogo pin?
POGO V.S Spring W 5W Same stroke B 1.9B Pogo pin`s advantage is reduced space in device design and it has no sliding friction like Spring pin, decrease contact area damage from friction. Mostly, POGO Pin`s life cycles more than Spring pin`s.
How to choose pogo pin height PCB solder tails?
How to choose POGO Pin height PCB PCB Plastic Housing Solder tails barrel piston ht Working height calculate: a. Largest working height: Height of Pogo – minimum 0.5mm b. The best suggest: Height of Pogo –The best suggestion ½ Stoke c.
How many lifetimes does a pogo pin have?
Voltage: 250V Life Cycles: 10000 ~100000cycles Plating: 20u” Gold on Plunger 10u” Gold on Barrel ~7.5mmStandard SPEC: Hollow Type POGO Pin Structure Piston Crimping Spring Barrel Solder tail Router of current Hollow type POGO Pin design for low space.