What is a #6 plane used for?

The No. 6, also called a “fore” hand plane is good for jointing edges and flattening and smoothing large surfaces, such as table tops, panels and workbench tops, where you might not want or need…

What is a Stanley No 6 plane used for?

Sized midway between a Jack and a Jointer, the No. 6 Fore Plane is designed to further true the surface after the Jack has sized it. Its length enables it to skim off high spots as it bridges low spots, delivering a leveled surface ready for the smoothing plane. 18″ long.

What do the numbers mean on Stanley planes?

The numbering system was devised about one hundred years ago at the Stanley Rule and Level Company to differentiate the size and types of planes they made. The numbers 1 to 8 simply refer to different lengths of plane with #1 being (very) short and #8 being pretty long.

How long is a #6 plane?

18” long
The No. 6 is 18” long, has an A2 cryogenically treated tool-steel iron that is 2-3/8” wide and . 140” thick, and the plane weighs in at 7-1/2 lbs.

What is a Jake plane?

The Aichi E13A (Allied reporting name: “Jake”) was a long-range reconnaissance seaplane used by the Imperial Japanese Navy (IJN) from 1941 to 1945. Numerically the most important floatplane of the IJN, it could carry a crew of three and a bombload of 250 kg (550 lb).

What plane should I buy first?

Your first purchases should be a low-angle block plane and a shoulder plane, above. Both help you put a refining touch on the less-than-perfect cuts produced by your power tools. For example, with a few strokes, a finely tuned low-angle block plane shaves burn marks or fuzz off end grain that saw blades leave behind.

What are the numbers on a planer?

The system’s smallest plane is the number 1, and its largest is the number 8. The full list of sizes are: 1, 2, 3, 4, 4-1⁄2, 5, 5-1⁄2, 6, 7, and 8. Stanley threw in some other oddball sizes, but nowadays these are the applicable planes.

What is a No 5 plane used for?

Bench or ‘Jack’ planes have a long base and are used for the initial preparation of rough timber. Made with a quality grey cast iron body for strength and stability with precision ground base and sides for flatness and squareness.

How big is a Stanley No 6 plane?

Length: 460 mm (18in). Cutter width: 60 mm (2.3/8in).

What is a jack plane used for?

A jack plane is a general-purpose woodworking bench plane, used for dressing timber down to size in preparation for truing and/or edge jointing. It is usually the first plane used on rough stock, but for rougher work it can be preceded by the scrub plane.

What is a number 5 plane used for?

What is No 7 plane used for?

In a traditional shop, the No. 7 is the most common size of jointer plane. It is used for shooting the long edges of boards to form them into a wider panel. And it is used for dressing the faces of boards to make accurate surfaces for joinery.

What kind of plane is a Stanley plane?

It has the prototypical construction details of a Stanley wartime plane, although wartime planes can contain a hodge-podge of parts. I was fortunate enough that the plane was in “new old stock” condition, which implies all original parts.

Is the Stanley wartime plane in original condition?

When did Stanley start casting model number into bed?

Stanley didn’t start casting the model number into the bed until around 1885 (the pre-lateral adjustment years), so you may have come across a very old one. Types are just a modern reference that mark the progression of feature changes through time.

When was the Stanley Bailey jointer plane made?

It’s a Stanley Bailey Jointer plane made between 1910 and 1924. I have a 608 with a patent date of Apr.2-95. I believe it’s a Bedrock? It doesn’t have flat sides, they are rounded like a Bailey.l Yes, you most likely have a Type 3 (1900-1908) Bed Rock.