How do I reset my AcuRite rain gauge?
Please press the “RESET” button for 1 second to clear the display and start counting from 00.00IN or 000.0MM. To change the outdoor rain gauge batteries, you must press and hold the “RESET” button for 5 seconds on the indoor rain monitor and let it re-sync again.
Why is my rain gauge not working?
To reset the rain gauge display, rain sensor or temperature sensor: Remove the batteries from the sensor and wait approximately 10 seconds. Replace the batteries in the sensor. To reset the sensor, press the reset button located under the cover of the rain sensor or in the battery compartment of the temperature sensor.
How do you calibrate an AcuRite self emptying rain gauge?
To adjust the rainfall reading by 10% turn both screws 1 full turn. There should be nearly an equal number of water drops between bucket tips. If not, then adjust the calibration screws beneath the tipping lever until an equal number of water drops are tipping the buckets. Then, restart the calibration procedure.
Where is the reset button on AcuRite weather station?
First, locate the reset button inside the battery compartment of the display unit. Press and release this button to factory reset the weather station. Once it is reset, press the GEO button to select the correct region that you’re in.
How do you reset an AcuRite outdoor sensor?
Hard Reset:
- Bring both the sensor and display unit together and power down by removing all batteries from each and/or removing the power cord.
- Change the A-B-C switch on both units to a new, matching channel then press and hold the reset button for 20 seconds if applicable.
- Reinstall the batteries in the outdoor sensor.
How do self emptying rain gauges work?
As rainfall fills the tiny bucket, it becomes overbalanced and tips down, emptying itself as the other bucket pivots into place for the next reading. The action of each tipping event triggers a small switch that activates the electronic circuitry to transmit the count to the indoor console, recording the event as .
How does AcuRite rain gauge?
The silver plug is a magnet and must be under the long plastic sleeve for it to register rain. Inside the sleeve is the reed switch, when the magnet passes back and forth, it opens/closes the reed switch and that is how the rain is measured.
How do you clean AcuRite rain gauge?
Clean the entire unit, whether you have a AcuRite Iris (5-in-1) or an AcuRite Atlas! Simply clean off the entire unit using a rag and warm soapy water. This will clear bugs, spiders, and spider webs away from any inlet areas in the solar radiation shield for more realistic temperature and humidity measurements.
How does the AcuRite rain gauge work?
Inside the sleeve is the reed switch, when the magnet passes back and forth, it opens/closes the reed switch and that is how the rain is measured. To test the rain gauge, slowly rock the tipping lever back and forth with your finger about 5 times.
How do I know if my rain gauge is accurate?
Tip: To have accurate results, ensure that all the water in the container is poured into the rain gauge before the test is complete. As the water flows into the rain gauge, the percentage error decreases until the measured value is the same as the expected rainfall. At that point, the error percentage is 0.00.
How accurate are rain gauges?
Analog rain gauges are very accurate with precise measurement markings, but some are highly accurate like the Stratus Precision Rain Gauge which is accurate to 1/100th of an inch.
How to read your rain gauge?
Here’s how: Check rain gauge. Get your rain gauge and make sure that it is empty even before the rainfall you are planning to measure pours. Read rain gauge on eye level. Once the rainfall has occurred, examine the filled rain gauge. Record water’s height. Do the recording of the water level’s height.
What are the types of rain guage?
Measuring Cylinder Rain Gauge. The simplest and most widely used rain gauges simply consist of a large cylinder,a funnel and a plastic measuring tube.
What are the uses of rain gauge?
A rain gauge is an instrument used by meteorologists and hydrologists to measure precipitation (e.g. rain) in a certain amount of time. It usually measures in millimetres.