Is triplet SF pet safe?
The WPS applies when this product is used to produce agricultural plants on farms, forests, nurseries, or greenhouses. For turf use, do not allow people (other than applicator) or pets on treatment area during application. Do not enter treatment areas until spray has dried.
When to apply Triplet SF?
Apply any time between the time when plants come into full leaf (spring) to when the plants begin to go dormant. Best results are obtained when weeds are young and actively growing. Do not cut weeds until herbicide has translocated throughout the plant causing root death.
How much Triplet SF per gallon of water?
For small (spot) applications with small tank sprayers, apply at the rate of 4 ounces of this product per gallon of water and spray to thoroughly wet all foliage.
How long does it take triplet to work?
Answer: It can take up to two weeks to start to see results after application of Triplet SF Selective Herbicide. 16 of 18 people found this answer helpful.
Does triplet SF need a surfactant?
Answer: Triplet SF Selective Herbicide does not require the use of a surfactant.
How long does triplet need to be on before rain?
For optimum results: (1) turf should not be mowed for 1 to 2 days before and after application; (2) do not apply if rain is expected within 4 hours after the application, delay irrigation cycle for 24 hours. Reseed no sooner than three to four weeks after application of this product.
How long does it take for triplet SF to work?
Answer: It can take up to two weeks to start to see results after application of Triplet SF Selective Herbicide.
How long should I wait to water after spraying for weeds?
Do not water right after applying a weed killer. Wait a minimum of two days before watering.
How many acres is triplet SF?
Details
| Active Ingredient | 2,4-D 30.56% Mecoprop-p 8.17% Dicamba 2.77% |
|---|---|
| Application | For control of broadleaf weeds, mix at a rate of 1.5 to 3.5 quarts of this product per acre in enough water to wet all parts of the foliage. This may require 50 to 300 gallons of water per acre. |
| Pet safe | Yes, if used as directed on label. |
How long after spraying par 3 is it safe?
It is degraded to water, carbon dioxide and humus. The process generally takes less than 30 days in the presence of warmth and moisture. PAR III does not leach into the subsoil. Watering a lawn within a day before or after spraying PAR III is NOT recommended, to allow the absorption of the chemical by the plants.
Should I mow weeds before spraying them?
A good rule of thumb is only apply pre-emergent herbicides to lawns more than a year old. Since pre-emergent herbicide must be washed into the soil to be effective, you can mow before applying it, however you should wait a few days after application to mow again.
Is Par 3 harmful to dogs?
The activity of the low dosage required when using PAR III in a spray mixture is effective on weeds, without being harmful to people and animals including pets, birds and insects. The amount applied is small and provides a large safety factor.
Which is the best triplet herbicide for turf?
PPE Fact Sheet Triplet SF is an effective liquid post-emergent broadleaf herbicide formulation of two phenoxy herbicides and dicamba that selectively controls broadleaf weeds in turfgrass. Triplet SF is perfect for control of hard-to-kill broadleaf weeds, such as dandelion, clover, henbit, and plantains in turfgrasses.
What kind of weeds can triplet SF kill?
Triplet SF is perfect for control of hard-to-kill broadleaf weeds, such as dandelion, clover, henbit, and plantains in turfgrasses. With the Optical Advantage®, Triamine is formulated to use a purified form of MCPP, known as the optical isomer.
When to cut weeds on a triplet lawn?
Do not cut weeds until herbicide has translocated throughout the plant causing root death. For control of woody plants, apply to both stems and foliage any time from the time foliage is completely matured until the time plants start to go dormant.
When is the best time to apply triplet?
Apply any time between the time when plants come into full leaf (spring) to when the plants begin to go dormant. Best results are obtained when weeds are young and actively growing. Do not cut weeds until herbicide has translocated throughout the plant causing root death.