What kind of pots does fender use?

What kind of pots does fender use?

Most Fender-type guitars use split-shaft pots, meaning the shaft of the control has a slit down the middle. That will let you squeeze the Fender Stratocaster style knob onto them. But some guitar controls have a little grub screw on the side and these need a solid shaft post, as that grub screw needs to grip tight.

What is the difference between A and B guitar pots?

500k “A” would denote an audio taper pot, and the “B” suffix would denote a linear taper pot. The only difference is the taper of the pot, or “how gradually it rolls off”. Most manufacturers use either (2) audio taper pots for volume + tone or would use audio taper for volume, and linear taper for tone.

What is the difference between 500K and 250k pots?

The rule is: Using higher value pots (500K) will give the guitar a brighter sound and lower value pots (250K) will give the guitar a slightly warmer sound. This is because higher value pots put less of a load on the pickups which prevents treble frequencies from “bleeding” to ground through the pot and being lost.

What are no load pots?

No-load tone pots look and function exactly like a regular tone pot. When turned between 1 – 9 it works like a regular tone pot. The difference is when the pot is rotated between 9 and 10, it acts as a true bypass system and essentially removes the tone pot and capacitor from the wiring circuit.

Are Fender pots any good?

Fender 500K, Split Shaft Potentiometer For Volume Or Tone This Taiwan-made potentiometer claims to be a genuine Fender replacement part of high-quality and durability. It seems most users had good results with this guitar pot and noted its quality.

Is upgrading guitar pots worth it?

In most cases, the stock electronics in an electric guitar or bass function just fine. When should you consider upgrading? 1. If there’s a problem — scratchy pots, loss of high frequencies when turning down, volume or tone taper that isn’t smooth, and so on — then an upgrade may improve the instrument.

Is there a difference between volume and tone pots?

Tone pot vs. People often ask “what’s the difference between a tone pot and volume pot?” The only difference between a tone pot and a volume pot is whether there is a capacitor attached. Since a potentiometer is a resistor, putting a cap between the pot and ground turns it into an EQ.

Are log Pots A or B?

The general convention for pots is that A is an audio/log taper and B is linear. For smooth control of volume, you should always use an A type audio/log taper pot.

What do capacitors do in guitars?

Capacitors, or “caps,” are simple electronic components that are typically used in guitar electronics as filters or barriers for certain frequencies. High frequencies will pass through a cap, while lower frequencies are blocked. The value of the capacitor will determine the frequencies that pass (refer to Diagram #7).

How do no load pots work?

What Are No-Load Pots? The design of the no-load pot causes it to remove itself from the circuit altogether when the volume reaches ten, by using a built-in off switch. The potentiometer will function as usual from one to nine, but shut off once it reaches ten and will no longer apply any resistance to the circuit.

How do pots work?

A potentiometer or “pot”, is a variable resistor that changes your tone or volume by increasing or decreasing resistance. Adding a capacitor or “cap” to the pot turns it into a simple EQ. Turning the wiper adjusts the amount of resistance and, in turn, determines which frequencies are allowed to pass.

How big is the pot on a Fender amp?

Fender® Pot Sets for many amps from the 1960s to the present. Top quality 24 mm carbon composition. 300 ° rotation. 1/2 watt, 500VDC rating. 1/4″ diameter solid metal shaft, 3/8″ bushing, solder lugs. Fits perfectly in vintage amps like Fender® (Tweed, Brownface, Blonde, original Blackface and original Silverface Models).

Is there a replica of a Fender Electric XII?

Back to the drawing board. This Electric XII replica started with an alder USA Custom Guitars Jazzymaster body with only the neck pocket and Gotoh XII bridge holes. Tommy at USACG did not have the tooling for the hockey stick headstock, so he suggested Best Guitar Parts for the neck.

What kind of pot does a Fender Silverface use?

Nylon shaft pots were used in most Fender silverface series amps from the late 60s and 70s. CTS was the original OEM supplier for vintage Fender® pots. 24 mm carbon composition. 300 ° rotation. 1/2 watt, 500VDC rating. 1/4″ diameter shaft, 3/8″ bushing, solder lugs, with push-pull SPST (two terminal) switch.

What kind of guitar is the Electric XII?

This Electric XII replica started with an alder USA Custom Guitars Jazzymaster body with only the neck pocket and Gotoh XII bridge holes. Tommy at USACG did not have the tooling for the hockey stick headstock, so he suggested Best Guitar Parts for the neck.