What is a Stihl 028 worth?
$125 is probably about the middle of average going rate of a WB. The 028 family are great saws imo.
How do you adjust the carburetor on a Stihl 028 chainsaw?
Go to full throttle, move the brake handle forward and let go of the throttle. The engine should not die down or run too slow and then pickup idle speed. In that case, open the L screw a bit till the idle speed drops, increase the idle by turning in the LA screw.
What year was Stihl 028 made?
The Stihl 028 was first introduced around 1977 and many of these saws have had very long, productive lives.
What size bar can I put on a Stihl 028?
As for bar length, an 028 AV Super has 3.5 HP. A 20 inch bar might be a tad much for it, especially in hardwoods. The Stihl bar selector guide says it will run a 20 inch OK.
Is Stihl 028 a pro saw?
No its not labeled a pro saw by Stihl, but it sure is built like one. The newer 029/MS290 “midrange” that replaced it doesn’t hold a candle to it as far as its construction. The 028 was a much more expensive saw for Stihl to manufacture and its evident quality shows it.
What replaced Stihl 028?
sawfun said: The replacement in similar quality of build plastic homeowner) for a standard 028 AV would be a ms241, and for an 028 super it would be a ms261. I would lean towards the 261 as it is still lighter than an 028 and has more power for not much money over a ms241. The 241’s advantage is it’s lighter weight.
How do you adjust a Stihl carburetor?
Start the trimmer and hold the throttle trigger in all the way to get the trimmer head spinning at maximum speed. Turn the H screw clockwise with a carburetor adjustment tool until the head is spinning as fast as it will go, then back off the screw carefully until the RPMs start to decrease.
How do you adjust the carburetor on a Stihl chainsaw?
They are the high-speed, low-speed and idle adjustments respectively. Determine the carburetor type before adjusting the high- and low-speed screws. To do this, turn the “L” screw clockwise as far as it will go, using a flat-head screwdriver, then turn it counterclockwise as far as it will go.
How old is a Stihl 028?
Stihl’s model 028 Wood Boss chain saw, called 028 WB for short, was manufactured in Germany and the United States primarily in the late 1970s through the 1980s.
What replaced the Stihl 028?
Is 028 wood boss a good saw?
The Woodboss is an older version of the 028 – has an aluminum tank (instead of plastic) and has points instead of Electronic ignition. They are great saws, but make sure you get one with low mileage – they are after all 20-25 years old… The 028 Super mentioned earlier is a really nice saw, but very hard to find.
Is the Stihl 028 chain saw Bullet Proof?
Stihl 028 Chainsaw Review Stihl 028 Chainsaw Even though the Stihl 028 chainsaw was first introduced over four decades ago it remains a really popular saw. It’s renowned for being a tough, virtually bullet proof and easy to use chainsaw.
When did the Stihl chain saw come out?
The Stihl 028 was first introduced around 1977 and many of these saws have had very long, productive lives. Who is the Stihl 028 Suitable For? A well maintained Stihl 028 is the perfect chainsaw if you are looking for an easy to use saw.
Do you need to change spark plug on Stihl 028 chainsaw?
028’s usually start easily after just a couple of pulls even in the cold. Most machines run well without constant adjustment. Minimal maintenance required during their lifetime other than replacing the obvious consumables like oil, spark plug, filters, chain, bar and sprocket.