How do you reset a Whirlpool Duet washing machine?

How do you reset a Whirlpool Duet washing machine?

Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.

How do you troubleshoot a Whirlpool Duet washer?

Troubleshooting Common Duet Washer Problems

1. Unplug the washer for 30 seconds to attempt to reset the Duet washer control.
2. Attempt a Duet Washer Quick Diagnostic Test.
3. Check the power supply at the wall with some other device. If the wall plug has power…
4. Check the Duet Line power filter.
5. Check power at the control.

Why does my Whirlpool Duet washer keep stopping?

Whirlpool Washer stops mid cycle If the washer door is not latched shut, the door switch prevents the washer from operating. If the door lock is defective, the washer may stop mid cycle. Inspect the door lock for damage. If the door lock is damaged or does not latch properly, replace it.

How do you clear the F11 code on a Whirlpool Duet washer?

To Fix Whirlpool Duet Washer F11 Error Code the first thing you need to do is check the wiring and connection between the central control unit and the motor control unit. Disconnect the wire at the central control unit from the motor control.

What is diagnostic mode on washer?

The washer’s diagnostic mode can be used to troubleshoot washer problems by viewing logged washer errors, performing an automatic diagnostic cycle, or manually turning on and off different washer parts to test for proper operation.

How long does a Whirlpool Duet washer last?

A washer can last between 12 and 14 years, while a dryer lasts between 18 and 24 years. The washer and dryer should last a long time.

Why does my front load washer stop mid cycle?

If a washer stops mid-cycle, it could be because the pump or the motor that runs it has failed. When this happens, it cannot remove the water efficiently, pump water in, and thus the sensors won’t allow it to move to the next cycle.

Why does my washer keep shutting off?

If the washing machine is a high efficiency model, it may stop automatically if it senses that there are too many suds in the washing machine tub. Other models will remain stopped until the situation is resolved by selecting a new rinse and drain cycle and allowing the water and suds to fully exit the machine.

Does a GE washer have a reset button?

Unplug the washer for one minute, then plug the washer back into the electrical outlet and lift and lower the lid six times within 12 seconds. This will reset the motor and you should be able to start the cycle.

Are there any problems with the Whirlpool duet washer?

Whirlpool duet washer is an amazing example of technology, but sometimes people claim to have problems with this washing machine. Some issues are easy to diagnose and has simple solutions. But a number of them are a bit critical to solve.

What are the error codes for a duet washer?

Duet Washer error and fault codes are displayed by alternating F#__ and E#__ The F error describes the washer system and the E error further defines the washer part that may be having a problem. F1, F2, F6 Are main control and program faults. F3 faults are washer sensor related problems. F5 faults are door lock and door switch related duet codes.

Why is my ge washing machine not spinning?

The washer will shut itself down to prevent any further damage. If your washing machine fills and agitates (washes) but doesn’t spin, the problem could also be with the lid switch, which tells the washer the lid is closed but may become dislodged by the vibrations of the spin cycle.

How to troubleshoot a ge top load washer?

1 Lid switch: The lid switch confirms that the lid is closed, allowing top-load washers to proceed with various stages of the cycle: fill, wash, drain, spin. 2 Pump: The pump actively removes water from your machine at the end of a cycle. 3 Drain hose: Your drain hose could have a kink or blockage that prevents drainage.