What does a boiler Plume KIT do?
A plume management kit is a simple device that is attached to your existing flue kit. It is essentially an extension of the flue pipe that is used to release the plume gases out at a more convenient direction and height.
How long can a plume kit be?
Flue accessories, such as plume displacement kits and plume deflectors, can be used to point the pluming away from the area that it is likely to cause an issue. At current, a production Baxi, Main or Potterton system or combi boiler with a 60/100mm concentric flue fitted, can be up to a maximum length of 10m.
What is a plume displacement kit?
Plume displacement terminal kit including 1m extension and brackets. Affixes to an existing Baxi horizontal flue terminal to allow exhaust plume gasses to escape in a different location, to avoid windows, vents or structures. For use with the current Baxi boiler range.
What is a boiler plume?
The “plume” Because the flue gases leaving a condensing boiler are cool, they tend to produce a noticeable mist or plume of water vapour around the flue terminal itself (as they condense upon contact with the atmosphere), especially under cold conditions.
Why do you need a plume kit?
Pluming can be a real problem in some installations, so rather than having to re-site the boiler the Worcester plume management kit directs the plume to an acceptable exit point away from doors, windows and neighbours.
How close can a boiler flue be to a boundary?
The minimum boiler flue installation distance requirement is 600 mm from an opposite wall, building, or fence. If the flue is installed facing the boundary, but on the back garden, then the minimum recommended distance is 300 mm.
When can a plume kit be used?
Plume Management kits used in carports If the exhaust terminal is extended at least 300mm beyond the footprint of the carport then the distance from the terminal to an opening within the carport can be reduced to 600mm.
What is the maximum length for a Worcester boiler flue?
1000mm for each 45° bend. Do not exceed the maximum straight length for a horizontal Ø60/100mm flue or a Ø60mm plume management system (if used) as stated in the relevant appliance Instruction Manual or addendum.
What is in plume from condensing boiler?
Modern condensing boilers extract more heat from the gas that is burnt. As soon as the flue gases contact the cold humid air, they begin producing long plumes of tiny water droplets. Generally, the colder the outside temperature the greater the plumage.
How much condensate does a combi boiler produce?
A general rule of thumb, 3.5 litres of condensate is produced for every 30kw of input providing the boiler is operating in full condensing mode. A boiler having 30kW of input operates for 1200 hours annually will produce approximately 4200 litres of condensate.
Can you flue into a Neighbours garden?
If the neighbours property goes right to your wall then you are not allowed because then your flue would be on their property, neither are you allowed to cause a nuisance, the plume from modern boilers can project 3 metres, there are also restrictions on boundaries, you cannot flue within a 600mm of your neighbours …
How long can a Worcester flue be?
With no cutting required, the flue measures 350mm in length but can be extended up to 570mm in total allowing for more flexible installation.
Who is required to install Worcester Bosch flues?
All Boilers and Boiler Accessories must be installed by a Qualified Gas Safe Registered professional. Worcester Bosch Plume Management Kits with multi-directional fluing.
How big is straight section of Worcester Bosch boiler?
” straight section is 500mm,if you require longer then you need to buy the seperate 1m section. ” 31 of 31 people found this review helpful. Was this review helpful? Yes
Why do you need a plume management kit?
The Plume Management Kit makes it easy to control the direction of the waste liquids & gases (plume) after they have been removed from the property via the flue.
Can a third party install a boiler and radiator?
As Boilers and radiators are installed by third parties, they do have to install in compliance with regulations and manufacturer standards to get the full benefit of the warranty. As long as these ar fulfilled, you will get the maximum life and support from your new purchase. Please mind that only logged in users can submit questions.