What is an electrical Lockout procedure?

What is an electrical Lockout procedure?

A lockout-tagout (LOTO) procedure is a safety system used to prevent accidental or unauthorized access to electrical power sources that are undergoing maintenance or other work.Muh. 24, 1441 AH

What is Lockout in electrical safety?

Lockout/tagout (LOTO) is a set of procedures that are used to ensure that equipment is shut down, inoperable, and (where relevant) de-energized. This allows maintenance and repair work on the system to be performed safely.Muh. 15, 1443 AH

How do you do an electrical lockout tagout?

The eight basic steps to a LOTO procedure are as follows:

1. Prepare for the shutdown.
2. Notify affected employees.
3. Shut down the equipment.
4. Isolate energy sources.
5. Apply LOTO devices to energy sources.
6. Release/control all stored energy.
7. Verify the lockout.
8. Maintain the lockout.

Who can remove energy control Lockout device?

worker
The Lockout Tagout devices are finally removed from an energy isolating device, only by the worker who applied it. The removal of employees lock without his knowledge can be dangerous, as a general rule, the Lockout Tagout device should be removed by the employee himself/herself. 5.

When should lockout be performed?

A lockout/tag out program will help prevent: Contact with a hazard while performing tasks that require the removal, by-passing, or deactivation of safe guarding devices. The unintended release of hazardous energy (stored energy). The unintended start-up or motion of machinery, equipment, or processes.

What must be done before removing locks and tags?

Inspect the work area to make sure all tools and items have been removed. Confirm that all employees and persons are safely located away from hazardous areas. Verify that controls are in a neutral position. Remove devices and re-energize machine.

What to do if an employee is not available to remove the lock?

Make all reasonable efforts to inform the absent Authorized Person that his/her lockout or tagout device needs to be removed. Make all reasonable efforts to inform the absent Authorized Person’s supervisor that his/her employee’s lockout or tagout device needs to be removed.

What must be performed immediately after locking out electrical equipment?

Shut Down – Power down the machine or equipment. Inform employees that will be affected by the shutdown of the equipment. Isolation – Make sure all sources of energy have been isolated. Turn off power, close valves, block moving parts, or disengage and block lines, etc.Muh. 13, 1442 AH

How do you isolate and lock out electrical equipment?

Unsafe electrical equipment must be isolated from energy sources, for example by using some of the following methods:

1. removal of fuses.
2. isolation of the drive motor at the source.
3. isolation of the control panel.
4. complete removal of power cable/plug from plant and equipment.
5. locking out the power supply board.

Is lockout/tagout required by OSHA?

In addition, 29 CFR 1910.333 sets forth requirements to protect employees working on electric circuits and equipment. This section requires workers to use safe work practices, including lockout and tagging procedures.

How do you install a lockout on a circuit breaker?

Use the push-button end to easily install these lockouts on circuit breakers with pin lockout holes on the inside of the circuit-breaker toggle switch that are mounted on DIN rails. Use the thumb wheel to install this lockout on circuit breakers with tie bars that are mounted on DIN rails.

What kind of lockout is used on electrical equipment?

Lock out a single energy control on machinery and electrical equipment so it can’t be used. Made entirely from nonconductive plastic for excellent electrical insulation. These have a chain to attach to equipment so they won’t get lost. Same as our other low-profile lockout hasps, but with an attached label to record employee name and department.

How does a lockout work on a gas valve?

Stop gas and fluid valve handles from opening and closing during maintenance. In addition to a hasp that interlocks when closed, lockout has an adapter to lock out a valve and a chain that attaches to equipment so it won’t get lost. A hinged design makes mounting these lockouts easy.

What do you need for a group lockout?

Sets contain items for group lockouts and are furnished in a yellow plastic case that mounts to the wall to keep the items organized in a central location. Each lockout rotates into itself, making installation in tight spaces easier than other lockouts. Sets come with red padlocks and hasps, as well as tags and a waist pouch.