What type of static route is created when the next hop?
What type of static route is created when the next-hop IP address and exit interface are specified? A fully specified static route has the next-hop IP address and exit interface specified. A recursive static route has only the next-hop IP address specified.
What can you use to identify the next hop in static route configuration?
The floating static route is only used when the primary route is not available. this, the floating static route is configured with a higher administrative distance than the primary route. The next hop can be identified by an IP address, exit interface, or both.
What are 4 types of static routes?
The following types of IPv4 and IPv6 static routes will be discussed:
- Standard static route.
- Default static route.
- Summary static route.
- Floating static route.
Can you have multiple static routes?
Important Points to Remember You can have multiple static routes and default gateways. You can have both IPv4 and IPv6 default gateways simultaneously. Static routes become active only when the nexthop is reachable.
What is next hop routing?
Next hop is a routing term that refers to the next closest router a packet can go through. Every single router maintains its routing table with a next hop address, which is calculated based on the routing protocol used and its associated metric.
Which two methods can be used to identify the next hop in a static route?
A parameter is used to create a floating static route by setting an administrative distance that is higher than a dynamically learned route. The next hop can be identified by an IP address, exit interface, or both.
What is a persistent route?
A persistent route stays in place even when Windows starts up. Using the same command we used earlier, you could make that route persistent with the following modification: route -p ADD 192.168.35.0 MASK 255.255.255.0 192.168.0.2.
What is static routing with example?
In production networks, static routes are mainly configured when routing from a particular network to a stub network. stub networks are networks that can only be accessed through one point or one interface….Static routing.
| Parameter | Meaning | example |
|---|---|---|
| Ip route | State that the route being configured is a static route | Ip route |
Which two methods can be used to identify the next hop in a static route choose two?
Why is a static route needed on both routers?
Static routing may have the following uses: Static routing can be used to define an exit point from a router when no other routes are available or necessary. This is called a default route. Static routing can be used for small networks that require only one or two routes.
Is next hop the same as Gateway?
Next hop is the next gateway to which packets should be forwarded along the path to their final destination. A routing table usually contains the IP address of a destination network and the IP address of the next gateway along the path to the final network destination.
How do you find next hop?
To determine the next hop for a given packet, the router will compare it to each of the entries in the routing table (by anding it with the netmask and comparing it to the network address). It will forward the packet to the first next-hop that matches.
Can a static route have a next hop address?
Configure a static route on R1 where the next hop cannot be recursive to another static route. Cisco recommends that you configure both the outbound interface and the next hop address for a static route.
When to specify outbound interface and next hop IP address?
Cisco highly recommends that you specify the outbound interface and the next hop IP address when you configure static routes. When the outbound interface is a point-to-point type of link (for example, a serial link), the specification of the next hop address is not needed.
What is the name of the ifcfg file?
Interface configuration (ifcfg) files control the software interfaces for individual network devices. As the system boots, it uses these files to determine what interfaces to bring up and how to configure them. These files are usually named ifcfg- name, where the suffix name refers to the name of the device that the configuration file…
When to use static routes in a problem scenario?
This document describes the basic concept of static routes. A problem scenario is used in order to demonstrate the circumstances in which it becomes desirable to specify the interface through which the next hop IP address can be reached when you configure a static route. Failure to do so can lead to unwanted behavior and a broken network state.